From 49b9b93b19fa4d4d8f27f4862b128f52cf4a5d28 Mon Sep 17 00:00:00 2001 From: Shin Sato Date: Sun, 21 Sep 2025 13:43:31 +0900 Subject: [PATCH] mediatek: add support for Buffalo WSR-6000AX8 and AX8P This commit adds support for Buffalo WSR-6000AX8 and AX8P models. Hardware -------- SOC: MediaTek MT7986B RAM: 512MB FLASH: 128MB SPI-NAND (Winbond) WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4 WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4 ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN) ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3) UART: 3.3V 115200 8N1 Serial(UART) Pin Layout ----------------------- +-------+-------+-------+-------+ J4 | RX | TX | GND |(3.3V) | +-------+-------+-------+-------+ (Bottom Side) MAC Address Table ----------------- lan1-3: board_data 0x4(text) eth1/WAN: board_data 0x4(text) WIFI 2.4G: lan1 + 2 WIFI 5G: lan1 + 9 Installation ------------ 1. Set up a TFTP server with the IP address "192.168.11.2". 2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it in the TFTP server's root directory. 3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P). 4. The device will automatically download the initramfs image from the TFTP server and boot into it. 5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image to complete the installation. Recovery -------- 1. Decrypt the official firmware image using "buffalo-enc". example: $ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \ -l -O 0xc8 2. Run "sysupgrade -F -n" with the decrypted image. Signed-off-by: Shin Sato Link: https://github.com/openwrt/openwrt/pull/13107 Signed-off-by: Hauke Mehrtens --- .../uboot-envtools/files/mediatek_filogic | 17 +- .../dts/mt7986b-buffalo-wsr-6000ax8.dts | 415 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 1 + .../base-files/lib/upgrade/platform.sh | 16 + target/linux/mediatek/image/filogic.mk | 13 + 5 files changed, 454 insertions(+), 8 deletions(-) create mode 100644 target/linux/mediatek/dts/mt7986b-buffalo-wsr-6000ax8.dts diff --git a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic index dd65d68779..3e26204454 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic @@ -81,6 +81,15 @@ jdcloud,re-cp-03) ;; esac ;; +buffalo,wsr-6000ax8|\ +mercusys,mr80x-v3|\ +mercusys,mr90x-v1|\ +routerich,ax3000|\ +routerich,ax3000-v1|\ +tenbay,wr3000k|\ +tplink,re6000xd) + ubootenv_add_mtd "u-boot-env" "0x0" "0x20000" "0x20000" "1" + ;; comfast,cf-e393ax|\ iptime,ax3000m) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x80000" @@ -103,14 +112,6 @@ gatonetworks,gdsp) glinet,gl-mt3000) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000" ;; -mercusys,mr80x-v3|\ -mercusys,mr90x-v1|\ -routerich,ax3000|\ -routerich,ax3000-v1|\ -tenbay,wr3000k|\ -tplink,re6000xd) - ubootenv_add_mtd "u-boot-env" "0x0" "0x20000" "0x20000" "1" - ;; openembed,som7981) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x80000" ubootenv_add_uci_sys_config "/dev/mtd3" "0x0" "0x100000" "0x100000" diff --git a/target/linux/mediatek/dts/mt7986b-buffalo-wsr-6000ax8.dts b/target/linux/mediatek/dts/mt7986b-buffalo-wsr-6000ax8.dts new file mode 100644 index 0000000000..408aece6ee --- /dev/null +++ b/target/linux/mediatek/dts/mt7986b-buffalo-wsr-6000ax8.dts @@ -0,0 +1,415 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include +#include +#include +#include + +#include "mt7986b.dtsi" + +/ { + model = "Buffalo WSR-6000AX8"; + compatible = "buffalo,wsr-6000ax8", "mediatek,mt7986b"; + + aliases { + serial0 = &uart0; + + label-mac-device = &gmac0; + led-boot = &power_green; + led-failsafe = &power_amber; + led-running = &power_green; + led-upgrade = &power_green; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-override = "ubi.mtd=ubi"; + }; + + memory@40000000 { + reg = <0 0x40000000 0 0x20000000>; + device_type = "memory"; + }; + + leds { + compatible = "gpio-leds"; + + power_green: led-0 { + color = ; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + function = LED_FUNCTION_POWER; + }; + + power_amber: led-1 { + color = ; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + function = LED_FUNCTION_POWER; + }; + + led-2 { + color = ; + gpios = <&pio 14 GPIO_ACTIVE_LOW>; + function = LED_FUNCTION_WLAN; + }; + + led-3 { + color = ; + gpios = <&pio 15 GPIO_ACTIVE_LOW>; + function = LED_FUNCTION_WLAN; + }; + + led-4 { + color = ; + gpios = <&pio 17 GPIO_ACTIVE_HIGH>; + function = LED_FUNCTION_WAN; + }; + + led-5 { + label = "green:internet"; + gpios = <&pio 30 GPIO_ACTIVE_HIGH>; + function = LED_FUNCTION_INDICATOR; + }; + }; + + keys { + compatible = "gpio-keys"; + + key-reset { + label = "reset"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + key-wps { + label = "wps"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + /* GPIO 18 and 19 are a tri-state switch button with + * ROUTER / AP / WB. + */ + key-router { + label = "router"; + gpios = <&pio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + key-bridge { + label = "wb"; + gpios = <&pio 19 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + /* GPIO 20 is a switch button with AUTO / MANUAL. */ + key-manual { + label = "manual"; + gpios = <&pio 20 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_board_data_4 0>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy-handle = <&phy6>; + + nvmem-cells = <&macaddr_board_data_4 0>; + nvmem-cell-names = "mac-address"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <1500000>; + reset-post-delay-us = <2000000>; + + /* WAN 2.5Gbps phy: MaxLinear GPY211C */ + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + }; + + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = ; + bias-disable; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = ; + bias-disable; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = ; + }; + }; + + wf_dbdc_pins: wf_dbdc-pins { + mux { + function = "wifi"; + groups = "wf_dbdc"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = ; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + mediatek,bmt-remap-range = <0x0 0x580000>, + <0x3980000 0x7480000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + precal_factory_1010: precal@1010 { + reg = <0x1010 0x58810>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x1a00000>; + }; + + partition@1f80000 { + label = "Kernel2"; + reg = <0x1f80000 0x1a00000>; + }; + + partition@3980000 { + label = "glbcfg"; + reg = <0x3980000 0x200000>; + read-only; + }; + + partition@3b80000 { + label = "seccfg"; + reg = <0x3b80000 0x200000>; + read-only; + }; + + partition@3d80000 { + label = "board_data"; + reg = <0x3d80000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_board_data_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x11>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@3f80000 { + label = "debug_log"; + reg = <0x3f80000 0x900000>; + read-only; + }; + + partition@4880000 { + label = "WTB"; + reg = <0x4880000 0x2c00000>; + read-only; + }; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default", "dbdc"; + pinctrl-0 = <&wf_2g_5g_pins>; + pinctrl-1 = <&wf_dbdc_pins>; + + nvmem-cells = <&eeprom_factory_0>, <&precal_factory_1010>; + nvmem-cell-names = "eeprom", "precal"; + status = "okay"; + + band@0 { + reg = <0>; + nvmem-cells = <&macaddr_board_data_4 2>; + nvmem-cell-names = "mac-address"; + }; + + band@1 { + reg = <1>; + nvmem-cells = <&macaddr_board_data_4 9>; + nvmem-cell-names = "mac-address"; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index a7289b91df..95af3b04e3 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -9,6 +9,7 @@ mediatek_setup_interfaces() case $board in abt,asr3000|\ + buffalo,wsr-6000ax8|\ cmcc,rax3000m|\ h3c,magic-nx30-pro|\ netis,nx31|\ diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 8f9515e304..b7a06d09f2 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -12,6 +12,18 @@ asus_initial_setup() ubimkvol /dev/ubi0 -N jffs2 -s 0x3e000 } +buffalo_initial_setup() +{ + local mtdnum="$( find_mtd_index ubi )" + if [ ! "$mtdnum" ]; then + echo "unable to find mtd partition ubi" + return 1 + fi + + ubidetach -m "$mtdnum" + ubiformat /dev/mtd$mtdnum -y +} + xiaomi_initial_setup() { # initialize UBI and setup uboot-env if it's running on initramfs @@ -131,6 +143,7 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; + buffalo,wsr-6000ax8|\ cudy,wr3000h-v1|\ cudy,wr3000p-v1) CI_UBIPART="ubi" @@ -333,6 +346,9 @@ platform_pre_upgrade() { asus,zenwifi-bt8) asus_initial_setup ;; + buffalo,wsr-6000ax8) + buffalo_initial_setup + ;; xiaomi,mi-router-ax3000t|\ xiaomi,mi-router-wr30u-stock|\ xiaomi,redmi-router-ax6000-stock) diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 6cd12bc300..b326702417 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -601,6 +601,19 @@ endif endef TARGET_DEVICES += bananapi_bpi-r4-poe +define Device/buffalo_wsr-6000ax8 + DEVICE_MODEL := WSR-6000AX8 + DEVICE_VENDOR := Buffalo + DEVICE_ALT0_MODEL := WSR-6000AX8P + DEVICE_ALT0_VENDOR := Buffalo + DEVICE_DTS_DIR := ../dts + DEVICE_DTS := mt7986b-buffalo-wsr-6000ax8 + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware + IMAGE_SIZE := 26624k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += buffalo_wsr-6000ax8 + define Device/cetron_ct3003 DEVICE_VENDOR := Cetron DEVICE_MODEL := CT3003 -- 2.30.2