Rosen Penev [Sat, 15 Jun 2024 22:13:07 +0000 (15:13 -0700)]
ath79: sitecom,wlrx100: use nvmem
Userspace handling is deprecated.
Also use led-sources for simplicity.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20508
Signed-off-by: Hauke Mehrtens <[email protected]>
Rani Hod [Tue, 7 Oct 2025 14:54:55 +0000 (17:54 +0300)]
mediatek: filogic: add support for Widelantech WAP430X
This AX3000 flying saucer-shaped device is sold under a few names:
- Widelantech WAP430X
http://www.widelantech.com/?m=home&c=View&a=index&aid=131
- Felicomm
- UeeVii UAP200 (sold on amazon.com)
True name, as marked on the PCB and as appears in the DTS, is WAP430X.
Hardware:
- SoC: Mediatek MT7981B
- RAM: 256MiB DDR3
- ROM: 16MiB NOR flash (Winbond 25Q128JVSQ)
- Wired: one GbE RJ45 port
- Wireless: Mediatek MT7976CN DBDC
- Antennas: Internal (two 2.4 GHz 4.5 dBi, three 5 GHz 6 dBi)
- GPIO: two blue LEDs (status, WLAN), one button (reset)
- Power: DC5521 (12V) or 802.3af PoE (48V 0.3A)
- UART: J500 on PCB [3v3] (Rx) (Tx) (Gnd), 115200n
Original firmware is GECOOS 8.0_2024081000, a fork of OpenWrt 21.02
created by Widelantech. All ports are closed except 443 (web management
interface) and 80 (redirects to 443). UART is locked down, but U-Boot
bootloader is friendly.
Installation is done via UART (see note below).
Method 1: press any key during boot to enter MTK U-Boot bootloader,
then choose option 2 (Upgrade firmware) and upload sysupgrade binary
via TFTP (or via Xmodem).
Method 2: put sysupgrade binary on a webserver (http, not https); after
GECOOS loads, choose option 4 (固件在线升级 = online firmware upgrade)
in the menu and enter the URL to the sysupgrade binary.
Note: GECOOS has a slick web management, and firmware can be uploaded
at https://6.6.6.6/#/system/sysupgrade but it's still not clear how to
convert the sysupgrade binary to a factory binary accepted by the web
interface (WIP).
Signed-off-by: Rani Hod <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20402
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Fri, 14 Jun 2024 18:50:06 +0000 (11:50 -0700)]
ath79: ecb1xxx: use nvmem
Userspace handling is deprecated.
Also switch LED to led-sources for simplicity.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20529
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Fri, 28 Nov 2025 23:31:24 +0000 (15:31 -0800)]
gpio-button-hotplug: use devm_kmemdup_array
Eliminates a manual memcpy.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19932
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sun, 31 Aug 2025 21:01:55 +0000 (14:01 -0700)]
treewide: add const to static arrays
Allows more compiler optimization.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19932
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sun, 3 Nov 2024 22:11:30 +0000 (14:11 -0800)]
treewide: fix coccinelle checks
Unneeded semicolon
WARNING comparing pointer to 0
WARNING: NULL check before some freeing functions is not needed.
WARNING: casting value returned by memory allocation function to (u32 *)
ERROR: allocation function on line 378 returns NULL not ERR_PTR on failure
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19932
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sat, 22 Jun 2024 17:46:07 +0000 (10:46 -0700)]
ath79: ews511ap: use nvmem
Userspace handling is deprecated.
This is a weird one. It should be using u-boot,env, but the variable
name is unknown. Keep it as is.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20520
Signed-off-by: Hauke Mehrtens <[email protected]>
gongzi miao [Mon, 1 Dec 2025 11:30:51 +0000 (19:30 +0800)]
kernel: bump 6.12 to 6.12.60
changelog:
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.60
Signed-off-by: gongzi miao <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/21010
Signed-off-by: Hauke Mehrtens <[email protected]>
Sven Eckelmann [Mon, 1 Dec 2025 12:58:40 +0000 (13:58 +0100)]
realtek: dsa: rtl930x: Fix flow control with ingress shaping
Tests with ingress shaping and enabled flow control showed really high
packet loss. It seems like the MAC pause frames are not created correctly
when both burst high off is set to the same value as burst high on.
By default, RTL930x has set the burst high values to:
* on: 64K
* off: 32K
Using the same 1:2 ratio seems to solve the high packet loss rate during
UDP tests.
Fixes: 2e74eb6d93a7 ("realtek: dsa: rtl93xx: Support per port throttling")
Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/21011
Signed-off-by: Robert Marko <[email protected]>
Felix Fietkau [Mon, 1 Dec 2025 18:13:52 +0000 (18:13 +0000)]
openssl: fix AES-GCM-SIV and AES-SIV with zero-length messages
Fix the cipher implementation to avoid treating empty input as finalizer.
This issue is fixed in the openssl 3.6 branch, but the fix approach from
that branch is not suitable for 3.5, since the code is completely different.
Signed-off-by: Felix Fietkau <[email protected]>
Robert Marko [Mon, 1 Dec 2025 14:02:04 +0000 (15:02 +0100)]
qualcommax: fix CPR of_property_present conversion
CPR conversion to of_property_present is broken in multiple places, either
by leaving the comma after now the last argument or by attempting to replace
an instance that actually uses the returned length.
So, lets fix these in order for qualcommax to compile again.
Fixes: c9e7f32c4c09 ("treewide: use of_property_present")
Signed-off-by: Robert Marko <[email protected]>
Eric Schäfer [Tue, 12 Aug 2025 18:47:28 +0000 (18:47 +0000)]
qualcommax: ipq807x: add support for Zyxel NWA210AX
The Zyxel NWA210AX is a wall- and ceiling-mountable access point (AP).
Hardware specifications:
- SoC: Qualcomm IPQ8071A
- RAM: 1 GB (Samsung K4A8G165WC-BCTD)
- Flash: 8 MB (Winbond W25Q64DW), 256 MB (Winbond W29N02GZ)
- Ethernet: 1x 2.5 Gbps RJ45 port (QCA8081), 1x 1 Gbps RJ45 port (AR8033)
- WiFi: 2.4 GHz 802.11ax/b/g/n (QCN5024), 5 GHz 802.11 ac/ax/n (QCN5054)
- Power: DC 12V/PoE 802.3at
- Button: Reset
- LEDs: Multicolour red/green/blue/white via LP5562
Installation/flashing instructions:
1. In OEM web interface navigate to gear icon → System → SSH and enable SSH.
2. Log in via SSH (username/password are the same as for the web interface).
3. Run "debug dual-image show".
4. Verify that output is "Current Image num: 1".
5. If this is not the case (i.e. if the output is "Current Image num: 0"):
a. Either flash a fresh version of factory firmware, or
b. run "debug dual-image set boot-image image1" and then run "reboot".
6. Log in via SSH again and verify that output is "Current Image num: 1".
7. Rename "openwrt-qualcommax-ipq807x-zyxel_nwa210ax-squashfs-factory.bin" to
"openwrt.bin" to avoid upload errors in the OEM web interface.
8. Reopen OEM web interface, navigate to wrench icon → File Manager →
Firmware Package and upload the bin file. Once the upgrade process is
finished and OpenWrt has booted, the LED will light up green.
Switching between OpenWrt and OEM firmware:
- OpenWrt → Zyxel via ssh command "zyxel-bootconfig-ipq807x set image1".
- Zyxel → OpenWrt via ssh command "debug dual-image set boot-image image0".
This commit is based on the work of Pascal Beleiu <
[email protected]>:
93ca21f3 (qualcommax: ipq807x: add support for Zyxel NWA210AX, 2025-03-17)
Signed-off-by: Eric Schäfer <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19828
Signed-off-by: Robert Marko <[email protected]>
Rosen Penev [Mon, 1 Dec 2025 10:28:04 +0000 (02:28 -0800)]
ath79: add back mistakenly removed label
Fixes target builds.
Fixes: 592d4e6 ("ath79: mr600-v1: use led-sources for ath9k")
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/21008
Signed-off-by: Hauke Mehrtens <[email protected]>
Álvaro Fernández Rojas [Sun, 30 Nov 2025 16:09:46 +0000 (17:09 +0100)]
generic: 6.12: backport bcm63xx-spi CS deassertion fix
Backport fix for premature SPI CS deassertion on RX-only transactions from
linux v6.18, which is needed for bmips (bcm63xx).
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Rany Hany [Sat, 15 Nov 2025 15:32:31 +0000 (15:32 +0000)]
wifi-scripts: add beacon_prot and spp_amsdu support
This adds support for beacon_prot and spp_amsdu in hostapd and
beacon_prot in wpa_supplicant (spp_amsdu is not relevant there).
Both options are disabled by default unless set in the config.
Signed-off-by: Rany Hany <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20793
Signed-off-by: Hauke Mehrtens <[email protected]>
Shiji Yang [Tue, 21 Oct 2025 04:07:52 +0000 (12:07 +0800)]
ipq40xx: dts: remove useless ethernet0 alias for WIA3300-20
The MAC addresses of this device are not assigned by the bootloader.
Therefore, this alias is useless.
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20478
Signed-off-by: Hauke Mehrtens <[email protected]>
Shiji Yang [Tue, 21 Oct 2025 04:06:04 +0000 (12:06 +0800)]
ipq40xx: dts: convert WIA3300-20 SPI chipselect to hardware mode
On ipq40xx platform, some specific GPIO can be configured as hardware
controlled SPI CS pin. This commit is an example of how to convert the
chipselect pin to the hardware CS mode.
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20478
Signed-off-by: Hauke Mehrtens <[email protected]>
Rany Hany [Sat, 8 Nov 2025 16:48:13 +0000 (16:48 +0000)]
wifi-scripts: change wifi-station's mac option into list
In the past PR[1] to add SAE wifi-station support, a commenter[2] requested
that the mac option be changed into a list. After trying to migrate my old
RADIUS setup I found myself wanting this change as well as it would simplify
my config. This patch does precisely that. Old configs that specify
`option mac ....` still work without any issues.
This change was done for both PSK and SAE. The schema was updated as well.
[1]: https://github.com/openwrt/openwrt/pull/17145
[2]: https://github.com/openwrt/openwrt/pull/17145#issuecomment-
2523507953
Signed-off-by: Rany Hany <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/17650
Signed-off-by: Hauke Mehrtens <[email protected]>
Tomáš Macholda [Thu, 18 Sep 2025 11:08:52 +0000 (13:08 +0200)]
mvebu: add support for Turris MOX
Adds support for Turris MOX, a modular router extendable by board modules (MOX B-G).
You can explore the idea behind the modules at: https://mox-configurator.turris.cz/
More information about Turris MOX can be found here: https://docs.turris.cz/hw/mox/intro/
Also works with Turris Shield (Turris MOX A and C with a simplified OS UI).
Specifications:
-----------------------
MOX A
- SoC: Marvell Armada 3720
- RAM: 512/1024 MB, DDR3
- Memory:
- 8 MB SPI NOR Flash for U-Boot and rescue system
- SD card slot
- 1x RJ-45, 1Gbps
- 1x USB 3.0
- 1x activity LED
- 1x reset button
- SDIO header
- misc pin header (UART, GPIO, JTAG, ...)
MOX B, G
- 1x mPCIe slot
- 1x SIM slot
MOX C
- 4x RJ-45, 1Gbps
MOX D
- SFP, 2.5Gbps
MOX E
- 8x RJ-45, 1Gbps
MOX F
- 4x USB 3.0
Module support:
-----------------------
Additional packages are needed for some modules.
MOX A (core)
- works as is
MOX B, G (mPCIe, mPCIe passthrough)
- works as is
MOX C, E (4x, 8x RJ-45)
- kmod-dsa
- kmod-dsa-mv88e6xxx
MOX D (SFP)
- kmod-sfp
- kmod-phy-marvell-10g
MOX F (4x USB 3.0)
- works as is
Wi-Fi 5, 3x3 card (WLE900VX)
- kmod-ath10k
- ath10k-board-qca988x
- ath10k-firmware-qca988x
Wi-Fi 6, DBDC, 2x2 card (MT7915DAN)
- kmod-mt7915e
- kmod-mt7915-firmware
Interface naming:
-----------------------
- MOX A's RJ-45 is assigned to `eth0`.
- MOX C, E (4x, 8x RJ-45) are assigned to `lan<number>@eth1`
- If MOX D (SFP) is connected directly to MOX A, the resulting interface
is `eth1`. If it's connected through MOX E (8x RJ-45), the resulting
interface is `sfp@eth1`.
Quirks:
-----------------------
- MOX is sensitive to the order of connected modules. Verify that the
confguration is valid at: https://mox-configurator.turris.cz/
- `CONFIG_MOXTET` and `CONFIG_GPIO_MOXTET` need to be enabled in kernel
config. Moxtet is a bus protocol needed to discover and configure MOX
modules. It must be compiled into the kernel for the modules to work.
Though it's very small so it won't bloat up the kernel image.
Flashing instructions:
-----------------------
1. Download `openwrt-*-ext4-sdcard.img.gz` and `gunzip` it.
2. Insert an SD card and flash the image to it using dd:
dd if=openwrt-*-ext4-sdcard.img.gz of=/dev/mmcblk0 bs=4096 conv=fsync
3. Plug the SD card into MOX.
Troubleshooting:
-----------------------
- https://docs.turris.cz/hw/serial/#turris-mox
- https://docs.turris.cz/hw/mox/rescue-modes/
Signed-off-by: Tomáš Macholda <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20356
Signed-off-by: Hauke Mehrtens <[email protected]>
Rany Hany [Wed, 19 Nov 2025 18:55:48 +0000 (18:55 +0000)]
wifi-scripts: make ft_iface configurable
This is useful as there are cases where no network is configured
or the configured network is isolated (APs are blocked from
communicating with each other over it). In both cases, it would make
sense to set ft_iface to another interface dedicated to FT over DS
traffic.
Signed-off-by: Rany Hany <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20797
Signed-off-by: Hauke Mehrtens <[email protected]>
INAGAKI Hiroshi [Tue, 7 Oct 2025 14:53:32 +0000 (23:53 +0900)]
ath79: add support for NEC Aterm WF1200HP2
NEC Aterm WF1200HP2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router with FE
ports, based on AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A-2.5BG2A)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EM2I-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 4x 10/100 Mbps
- switch : Atheros AR9344 (SoC)
- LEDs/Keys (GPIO) : 12x/4x
- note : all LEDs are controlled by ath10k chip (QCA9882)
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8 (U-Boot: 115200n8)
- Power : 12 VDC, 0.7 A (Max. 8 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WF1200HP2 with router mode
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.10.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with sysupgrade.bin image
sysupgrade <sysuppgrade image>
8. Wait ~120 seconds to complete flashing and rebooting
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WF1200HP2 and interrupt bootloader by ESC key
3. Login to the bootloader CLI with the password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, backup the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the
device
9. Replace the bootloader with uboot.bin image (see above)
10. Perform sysupgrade with sysupgrade.bin image (see above)
11. Wait ~120 seconds to complete flashing and rebooting
Notes:
- The stock bootloader requires the unknown filesystem on firmware area
in the flash chip. Booting OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
Known issues:
- All LEDs on the front side are connected to the GPIO controller on the
ath10k chip (QCA9882) and controlled by it. The current ath10k driver
supports only one LED as "ath10k-phyN", but using as a GPIO controller
is not supported yet. As a result, all 12x LEDs on the front side
cannot be controlled by users.
MAC Addresses:
LAN : C0:25:A2:xx:xx:44 (config, 0x6 (hex))
WAN : C0:25:A2:xx:xx:45 (config, 0xc (hex))
2.4 GHz: C0:25:A2:xx:xx:46 (config, 0x0 (hex))
5 GHz : C0:25:A2:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20611
Signed-off-by: Hauke Mehrtens <[email protected]>
INAGAKI Hiroshi [Tue, 7 Oct 2025 14:53:32 +0000 (23:53 +0900)]
ath79: add support for NEC Aterm WF1200HP
NEC Aterm WF1200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router with FE
ports, based on AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A-2.5BG2A)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EM2I-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 4x 10/100 Mbps
- switch : Atheros AR9344 (SoC)
- LEDs/Keys (GPIO) : 12x/4x
- note : all LEDs are controlled by ath10k chip (QCA9882)
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8 (U-Boot: 115200n8)
- Power : 12 VDC, 0.7 A (Max. 8 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WF1200HP with router mode
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.10.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with sysupgrade.bin image
sysupgrade <sysuppgrade image>
8. Wait ~120 seconds to complete flashing and rebooting
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WF1200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with the password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, backup the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the
device
9. Replace the bootloader with uboot.bin image (see above)
10. Perform sysupgrade with sysupgrade.bin image (see above)
11. Wait ~120 seconds to complete flashing and rebooting
Notes:
- The stock bootloader requires the unknown filesystem on firmware area
in the flash chip. Booting OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
Known issues:
- All LEDs on the front side are connected to the GPIO controller on the
ath10k chip (QCA9882) and controlled by it. The current ath10k driver
supports only one LED as "ath10k-phyN", but using as a GPIO controller
is not supported yet. As a result, all 12x LEDs on the front side
cannot be controlled by users.
MAC Addresses:
LAN : C0:25:A2:xx:xx:44 (config, 0x6 (hex))
WAN : C0:25:A2:xx:xx:45 (config, 0xc (hex))
2.4 GHz: C0:25:A2:xx:xx:46 (config, 0x0 (hex))
5 GHz : C0:25:A2:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20611
Signed-off-by: Hauke Mehrtens <[email protected]>
INAGAKI Hiroshi [Thu, 30 Oct 2025 11:25:19 +0000 (20:25 +0900)]
uboot-ath79: add FE profile for NEC Aterm series (AR9344)
Add ar9344_nec_aterm_fe profile for NEC Aterm WF1200HP and WF1200HP2
based on Atheros AR9344, but using internal FE switch instead of
external GbE switch.
Signed-off-by: INAGAKI Hiroshi <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20611
Signed-off-by: Hauke Mehrtens <[email protected]>
Andrew LaMarche [Wed, 19 Nov 2025 16:28:19 +0000 (11:28 -0500)]
ramips: add support for TP-Link Archer AX21
This patch adds support for the TP-Link Archer AX21 v4.
Device specification
--------------------
SoC Type: Mediatek MT7621DAT
RAM: DDR (128MB)
Flash: ESMT EN25QH128A (16MB)
Ethernet: 5x (4 lan, 1 wan) via embedded switch/SoC built-in
Wi-Fi: 2x2 2.4GHz via MT7975DN, 2x2 5GHz via MT7905DAN
LEDs: Power, 2.4GHz, 5GHz, WAN, LAN, WPS
Buttons: Reset, WPS
Installation
------------
Upload the factory image using the Web UI.
Signed-off-by: Andrew LaMarche <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20932
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sat, 4 Oct 2025 22:22:58 +0000 (15:22 -0700)]
ath79: ubnt: nvmem calibration
Userspace handling is deprecated.
Moved pcie wifi nodes out of dtsi as these devices differ in wifi
chipsets and thus calibration size. Added compatible lines too.
Removed pointless label_mac assignments as label-mac-device is already
implemented.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20303
Signed-off-by: Hauke Mehrtens <[email protected]>
Richard Fröhning [Sun, 16 Nov 2025 14:07:35 +0000 (15:07 +0100)]
mediatek-filogic: assign WAN netdev trigger to blue:wan LED for cudy wr3000e
- rename blue:wan-online to blue:wan
- assign wan netdev trigger to blue:wan
Signed-off-by: Richard Fröhning <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20808
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sun, 25 May 2025 21:20:28 +0000 (14:20 -0700)]
ath79: ar9344: use led-sources for ath9k
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19865
Signed-off-by: Hauke Mehrtens <[email protected]>
Til Kaiser [Mon, 24 Nov 2025 14:50:33 +0000 (15:50 +0100)]
ramips: mt76x8: add Teltonika RUT976 support
This commit adds support for the Teltonika RUT976, part
of the RUTE series, which is very similar to the RUT956.
The RUT976 now has a 5G modem and the flash size has doubled.
Specification:
- MediaTek MT7628AN SoC
- 128 MB RAM
- 32MB Flash
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- MediaTek MT7628AN 2.4 GHz 802.11n WiFi
- Quectel RG255C 5G modem
- GNSS
- RS232, DB9 connector, Cypress ACM via USB, /dev/ttyACM0
- RS485 /dev/ttyS1
- microSD card slot
- 2.0 USB Type-A HOST port
- analog 0-24V input (MCP3221)
- Relay
- 2x Digital input
- 2x Digital output
- 2x SIM slot (can be swapped via GPIO)
- eSIM (depends on hardware configuration, can be swapped via GPIO)
GPIO:
- 1 button (Reset)
- 7 LEDs (power, status green/red, RSSI 1,2,3,4,5)
- 5 Modem control (power button, reset, status, SIM select, eSIM select)
- 2 Digital input
- 2 Digital output
- 1 Isolated input
- 1 RS485 tx enable
- 1 RS485 rx enable
- 1 Relay
- 1 Data Carrier Detect (DCD)
Flashing via OEM WebUI:
1. Download the firmware image *-squashfs-factory.bin
2. Upload firmware image via OEM WebUI firmware update, do not keep settings
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile data connection:
Create proto qmi interface.
Signed-off-by: Til Kaiser <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <[email protected]>
Til Kaiser [Tue, 25 Nov 2025 10:43:22 +0000 (11:43 +0100)]
uqmi: skip registration state check if not supported
The Quectel RG255C modem used in the Teltonika RUT976 does not support
the 'Get Serving System' QMI command, returning "Invalid QMI command".
Without this change, the script would fail even though the connection
could be established successfully.
This patch skips the registration state check if the command is not
supported and relies on subsequent checks instead.
Signed-off-by: Til Kaiser <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <[email protected]>
Til Kaiser [Mon, 24 Nov 2025 14:49:47 +0000 (15:49 +0100)]
generic: 6.12: backport net-usb-qmi_wwan: add Quectel RG255C
Backport support for the Quectel RG255C USB modem.
This modem is used, among others, on the Teltonika RUT976.
Signed-off-by: Til Kaiser <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <[email protected]>
Til Kaiser [Mon, 24 Nov 2025 14:49:09 +0000 (15:49 +0100)]
ramips: split Teltonika RUT9M SPI-NOR layout into separate dtsi
Introduce mt7628an_teltonika_rut9m.dtsi to hold the SPI-NOR flash
definition and partition layout specific to the RUT9M series.
This refactor prepares for supporting the Tetonika RUT976
(part of the RUTE series), which shares most hardware with
RUT9M devices but has a different flash layout.
Update RUT9x1 and RUT9x6 DTS files to include the new dtsi.
Existing RUT9M devices remain unchanged.
Signed-off-by: Til Kaiser <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <[email protected]>
Schneider Azima [Fri, 28 Nov 2025 10:37:25 +0000 (05:37 -0500)]
mediatek: add support for Mercusys MR85X
This commit adds support for Mercusys MR85X router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: Realtek rtl8367s + 2.5Gbe Airoha en8811h
- Ethernet: 1x2.5Gbe (WAN 2.5Gbps), 3xGbe (LAN 1Gbps, port0, port1, port2)
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 amber and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 2 (reset,wps)
- Bootloader: Main U-Boot - U-Boot 2022.07-rc3. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.07-rc3)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 00:FF:xx:xx:xx:EE | label |
| WAN | 00:FF:xx:xx:xx:EF | label+1 |
| LAN | 00:FF:xx:xx:xx:EE | label |
| WLAN 2g | 00:FF:xx:xx:xx:ED | label-1 |
| WLAN 5g | 00:FF:xx:xx:xx:EC | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file "default-mac".
OEM wireless eeprom is also there, file "MT7981_EEPROM.bin".
Signed-off-by: Schneider Azima <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19187
Signed-off-by: Hauke Mehrtens <[email protected]>
Schneider Azima [Fri, 28 Nov 2025 10:34:02 +0000 (05:34 -0500)]
mediatek: build rtl8367s_gsw as a kernel module
The RTL8367S_GSW config for filogic target is not set by default.
This switch model can be recognized by multiple drivers. Configure it as an optional module instead of default set in config.
Signed-off-by: Schneider Azima <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19187
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Thu, 27 Nov 2025 07:24:16 +0000 (23:24 -0800)]
kernel: remove uboot,env hack
Since everything got migrated to the layouts driver, this is no longer
needed.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20948
Signed-off-by: Hauke Mehrtens <[email protected]>
Aleksander Jan Bajkowski [Sat, 29 Nov 2025 16:55:41 +0000 (17:55 +0100)]
kernel: backport upstream Realtek PHY patches
Backport of the latest upstream Realtek PHY patches. WoL uses
devm_pm_set_wake_irq(), so the patch that adds this function
has also been backported.
Changelog:
4465ae435ddc net: phy: realtek: create rtl8211f_config_phy_eee() helper
bb78b71faf60 net: phy: realtek: eliminate priv->phycr1 variable
e1a31c41bef6 net: phy: realtek: allow CLKOUT to be disabled on RTL8211F(D)(I)-VD-CG
910ac7bfb1af net: phy: realtek: eliminate has_phycr2 variable
27033d069177 net: phy: realtek: eliminate priv->phycr2 variable
8e982441ba60 net: phy: realtek: create rtl8211f_config_rgmii_delay()
b826bf795564 net: phy: realtek: fix RTL8211F wake-on-lan support
Tested on Netgear WAX206 with RTL8221B-VB-CG.
Signed-off-by: Aleksander Jan Bajkowski <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20987
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Thu, 4 Sep 2025 02:01:49 +0000 (19:01 -0700)]
treewide: use of_property_present
Easier to read and reason about.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19951
Signed-off-by: Hauke Mehrtens <[email protected]>
Hauke Mehrtens [Sat, 29 Nov 2025 18:05:42 +0000 (19:05 +0100)]
toolchain: glibc: Update glibc 2.41 to recent HEAD
373408c19f stdlib: resolve a double lock init issue after fork [BZ #32994]
62928cf7d8 elf: Do not add a copy of _dl_find_object to libc.so
f48de98bce elf: Extract rtld_setup_phdr function from dl_main
513629b14d elf: Handle ld.so with LOAD segment gaps in _dl_find_object (bug 31943)
1502c248d5 nptl: Fix SYSCALL_CANCEL for return values larger than INT_MAX (BZ 33245)
daa4de5253 AArch64: Avoid memset ifunc in cpu-features.c [BZ #33112]
0bb6dad5af AArch64: Optimize algorithm in users of SVE expf helper
2a0b52fdd6 AArch64: Optimize inverse trig functions
307a8a4434 AArch64: Improve codegen in SVE log1p
503f7a7d33 AArch64: Optimize SVE exp functions
6db0f659c8 AArch64: Optimise SVE FP64 Hyperbolics
c467918138 AArch64: Improve codegen SVE log1p helper
330cd035df Remove <libc-tsd.h>
f409ec073f Use proper extern declaration for _nl_C_LC_CTYPE_{class,toupper,tolower}
5d8614b284 ctype: Fallback initialization of TLS using relocations (bug 19341, bug 32483)
940d821afb Use TLS initial-exec model for __libc_tsd_CTYPE_* thread variables [BZ #33234]
4a3e5f1e4c elf: Introduce separate _r_debug_array variable
9d6577fdff elf: Introduce _dl_debug_change_state
b05ce0de3d elf: Restore support for _r_debug interpositions and copy relocations
85780b6055 elf: Compile _dl_debug_state separately (bug 33224)
dd87fcda43 x86-64: Add GLIBC_ABI_GNU2_TLS version [BZ #33129]
e2d9e9eb26 x86-64: Add GLIBC_ABI_DT_X86_64_PLT [BZ #33212]
3f3b4fdd0b elf: Fix handling of symbol versions which hash to zero (bug 29190)
42f9c70ac2 elf: Test dlopen (NULL, RTLD_LAZY) from an ELF constructor
aa5dbd5332 elf: Preserve _rtld_global layout for the release branch
c1bec0b52d i386: Update ___tls_get_addr to preserve vector registers
7aa907241c i386: Also add GLIBC_ABI_GNU2_TLS version [BZ #33129]
ed4672abb5 i386: Add GLIBC_ABI_GNU_TLS version [BZ #33221]
a52c9b75c7 Optimize __libc_tsd_* thread variable access
9867e44cdc AArch64: Fix SVE powf routine [BZ #33299]
cf926cd7fb nss: Group merge does not react to ERANGE during merge (bug 33361)
4b1f8c90f9 x86: Detect Intel Wildcat Lake Processor
7c0632472d x86: Detect Intel Nova Lake Processor
580746904b x86: fix wmemset ifunc stray '!' (bug 33542)
1f57ffdf35 aarch64: Disable ZA state of SME in setjmp and sigsetjmp
97076e0cf1 aarch64: update tests for SME
1a0ee26714 aarch64: define macro for calling __libc_arm_za_disable
889ae4bdbb aarch64: clear ZA state of SME before clone and clone3 syscalls
e4ffcf32b9 aarch64: tests for SME
5bf8ee7ad5 aarch64: fix cfi directives around __libc_arm_za_disable
75b6b263e9 aarch64: Do not link conform tests with -Wl,-z,force-bti (bug 33601)
215e9155ea aarch64: fix includes in SME tests
360f60fb63 AArch64: Optimise SVE scalar callbacks
ca489fc802 AArch64: Fix instability in AdvSIMD tan
442cc3901b AArch64: Fix instability in AdvSIMD sinh
1e16b570bb AArch64: fix SVE tanpi(f) [BZ #33642]
5c6445672a AArch64: Fix and improve SVE pow(f) special cases
040256e79b ppc64le: Restore optimized strcmp for power10
f8cdc03e1e ppc64le: Restore optimized strncmp for power10
6a0b8e3665 ppc64le: Power 10 rawmemchr clobbers v20 (bug #33091)
Link: https://github.com/openwrt/openwrt/pull/20989
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Fri, 28 Nov 2025 02:31:52 +0000 (18:31 -0800)]
ath79: convert pcie gpios to led-sources
Simpler dts.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19860
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sun, 25 May 2025 00:11:32 +0000 (17:11 -0700)]
ath79: fix some ath10k LEDs
ath10k loads before ath9k and thus ends up as phy0.
Also use led-sources to avoid some confusion.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19860
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Sun, 25 May 2025 21:07:00 +0000 (14:07 -0700)]
ath79: mr600-v1: use led-sources for ath9k
The ath9k driver creates an ath9k LED by default. Instead of having a non
functional LED, configure it properly and remove the extra as it's not
needed.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19860
Signed-off-by: Hauke Mehrtens <[email protected]>
Vincent Li [Fri, 28 Nov 2025 17:56:04 +0000 (09:56 -0800)]
loongarch64: add Loongson PCI DWMAC as built-in
Add the CONFIG_DWMAC_LOONGSON driver to the loongarch64 kernel
configuration as a built-in module.
This driver is required for the integrated Ethernet controller found on
modern Loongson devices such as the 3A6000 NUC and 2K3000. Including it
by default ensures these popular devices have network functionality
out-of-the-box.
Configuration changes were made via `make kernel_menuconfig` for the
loongarch64 target.
Ref: https://github.com/openwrt/openwrt/issues/20945
Signed-off-by: Vincent Li <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20975
Signed-off-by: Hauke Mehrtens <[email protected]>
Brian Lee [Fri, 28 Nov 2025 05:37:15 +0000 (14:37 +0900)]
mediatek: filogic: add support for ASUS TUF-AX4200Q
ASUS TUF-AX4200Q(TUF 小旋风Pro WiFi6 AX4200) is a home router that adds an additional 2.5G Ethernet port to ASUS TUF-AX4200.
Hardware
- - - - - - - -
- SOC : MediaTek MT7986
- RAM : 512MB DDR3
- FLASH : 256MB SPI-NAND (Winbond W25N02KV)
- WIFI : Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
- ETH : MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
- UART : 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
- - - - - - - -
Vendor-UI Method:
1. Download or make the OpenWrt initramfs.trx image
2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1/
4. If your router is brand new, finish the setup process and log into the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
TFTP Method:
1. Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24.
Rename the image to tufax4200q.bin.
2. Connect the PC with TFTP server to the TUF-AX4200Q.
Set a static ip on the ethernet interface of your PC.
(IP address: 192.168.1.70, subnet mask: 255.255.255.0)
Connect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 tufax4200q.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot.
Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
(based on support for ASUS RT-AX52 by achterin and trx image generation by remittor)
Signed-off-by: Brian Lee <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20900
Signed-off-by: Hauke Mehrtens <[email protected]>
Alexandru Gagniuc [Fri, 7 Nov 2025 03:52:11 +0000 (21:52 -0600)]
qualcommbe: update ipq9574 PCS driver
Update the ipq9574 PCS driver the version provided by Qualcomm via
github. The updated driver simplifies link up handling by removing
unnecessary clock rate changes.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20993
Signed-off-by: Robert Marko <[email protected]>
Alexandru Gagniuc [Fri, 7 Nov 2025 02:59:37 +0000 (20:59 -0600)]
qualcommbe: drop "uniphy" from pcs node labels
According to Qualcomm developers, the pcs nodes on IPQ9574 will be
labeled "pcs<n>" and "pcs<n>_ch<m>". The proposed IPQ5424 changes
include the simpler labels. Rename the IPQ95xx nodes for consistency.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20993
Signed-off-by: Robert Marko <[email protected]>
Alexandru Gagniuc [Thu, 27 Nov 2025 20:11:11 +0000 (14:11 -0600)]
qualcommbe: use ipq_pcs_get/put() in PPE (MAC) driver
ipq_unipcs_create/destroy() are provided by an older version of the
IPQ9574 PCS driver. Use the renamed versions ipq_pcs_get/put() to
allow updating the PCS driver.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20993
Signed-off-by: Robert Marko <[email protected]>
Álvaro Fernández Rojas [Fri, 28 Nov 2025 11:00:30 +0000 (12:00 +0100)]
odhcp6c: update to Git HEAD (2025-11-24)
f98b6ec82362 all: implement RFC8910 §3 URI equality check
3484787e9a5b all: implement RFC8910 captive portal (CP) option
25a0c40580f9 dhcpv6: refactor variable names
165bcc68ef2b dhcpv6: refactor variable names
8f60e7b1833c dhcpv6: refactor variable names
319305fceeef dhcpv6: refactor variable names
dcb53c496513 dhcpv6: assign a new field for prefix exclusion length
080b64d70e73 dhcpv6: refactor variable names
66dd9b26b73a dhcpv6: refactor variable names
f038a50604ae odhcp6c: set environment script to its current location
5f63e7e47dfc github: ci: add MIPS64, PowerPC64 and RISCV64
038407eca8a4 dhcpv6: restart DHCPv6 on receipt of RA containing a new prefix
af9968c0293f dhcpv6: fix processing PIO exclusion loop variable collision
5492f09ec075 odhcp6c: apply draft-ietf-6man-slaac-renum-11 lifetime rules
38a31eb29a48 src: add fallthrough attribute
b46d79c8792c odhcp6c: properly guard attributes
https://github.com/openwrt/odhcp6c/compare/
cbc8ff0e6226...
f98b6ec82362
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Rosen Penev [Thu, 18 Sep 2025 23:15:02 +0000 (16:15 -0700)]
mediatek: rtl8367s: modernize gpio API
Upstream is strongly considering removing of_gpio.h. As of this commit,
3 upstream drivers remain with actual usage.
Get ahead of upstream and use the GPIOD API before the OF one goes away.
Rework to remove mediatek,reset-pin in favor of the standard
reset-gpios.
Fix wrong high GPIO.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20088
Signed-off-by: Hauke Mehrtens <[email protected]>
Coia Prant [Wed, 1 Oct 2025 10:04:26 +0000 (18:04 +0800)]
ramips: add support for Hongdian H8850 v20
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628DAN
- Flash: 16 MB
- RAM: 64 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN/LAN, 3x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (PWR): Always Off
Modem (NET): GPIO/3 active-low
LAN: Always On
RF (Modem Signal): GPIO/2 active-low
WIFI: GPIO/44 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using TTL:
1. Connect the board to the computer via TTL.
2. Enter original firmware failsafe mode.
3. Use wget download firmware to board /tmp
4. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h8850-v20-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8850-v20-and-flash.html
Signed-off-by: Coia Prant <[email protected]>
Tested-by: Coia Prant <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20259
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Fri, 28 Nov 2025 20:20:45 +0000 (12:20 -0800)]
qualcommbe: fix wrongly edited patch
Line count was incorrect
Fixes: 96fc2fa ("treewide: convert u-boot,env to nvmem-layout")
Signed-off-by: Rosen Penev <[email protected]>
George Sapkin [Tue, 25 Nov 2025 12:10:50 +0000 (14:10 +0200)]
formal: fix workflow permissions
Fix formality check permissions that are needed to post optional
summaries back to the PR.
Link: https://github.com/openwrt/actions-shared-workflows/pull/64
Signed-off-by: George Sapkin <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20930
Signed-off-by: Robert Marko <[email protected]>
Shiji Yang [Sat, 29 Nov 2025 17:02:12 +0000 (18:02 +0100)]
ipq40xx: convert CRLF line-ending to LF for Linksys MR6350
Use Unix LF style instead of Windows CRLF style.
Fixes: 00bb18b851df ("ipq40xx: Add support for Linksys MR6350")
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20973
Signed-off-by: Robert Marko <[email protected]>
Robert Marko [Sat, 29 Nov 2025 16:56:11 +0000 (17:56 +0100)]
Revert "treewide: fixup ath10k nodes"
This reverts commit
741689a335de75430dc505bcdb9326bf1149f807.
Only after merging I remebered the reason why it was changed to 0,0 [1].
[1] https://github.com/openwrt/openwrt/commit/
1e20f7b6c61ded7a77ebee76b59612c76d76b9f2
Signed-off-by: Robert Marko <[email protected]>
Shiji Yang [Sat, 29 Nov 2025 09:06:28 +0000 (17:06 +0800)]
gitattributes: automatically convert dts file CRLF line endings to LF
It seems that some developers prefer to use the Windows OS to add new
device support. Add new attributes for device tree files so that the
CRLF line endings can be automatically normalized to LF.
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20978
Signed-off-by: Robert Marko <[email protected]>
Rosen Penev [Wed, 8 Oct 2025 23:05:25 +0000 (16:05 -0700)]
ramips: rt3xxx: fix wifi node address
The reg value says it should be wifi@1,0, not wifi@0,0.
Should fix dtc warning.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20351
Signed-off-by: Robert Marko <[email protected]>
Rosen Penev [Sun, 8 Jun 2025 00:35:33 +0000 (17:35 -0700)]
treewide: fixup ath10k nodes
Use compatible before reg for consistency.
Also fixup the wifi node name for some qualcomm platforms where the slot
is 1 instead of 0.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20351
Signed-off-by: Robert Marko <[email protected]>
Rosen Penev [Sun, 25 May 2025 21:17:22 +0000 (14:17 -0700)]
ath79: tplink_tl-wdrxxxx: use led-sources for ath9k
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19861
Signed-off-by: Hauke Mehrtens <[email protected]>
Hauke Mehrtens [Thu, 27 Nov 2025 21:27:55 +0000 (22:27 +0100)]
uboot-mediatek: mtd: spinand: esmt: add support for F50L1G41LC
Add support for esmt F50L1G41LC flash chip. It is used in some recent
Cudy devices.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <[email protected]>
Hauke Mehrtens [Thu, 27 Nov 2025 20:13:04 +0000 (21:13 +0100)]
kernel: mtd: spinand: esmt: add support for F50L1G41LC
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <[email protected]>
George Moussalem [Thu, 23 Oct 2025 11:16:21 +0000 (15:16 +0400)]
qualcommax: ipq50xx: split firmware variants and refactor QCN6122 support
IPQ5018 based boards come in multiple wireless architectures.
The SOC itself provides 2.4G wifi while 5G wifi is added by either an
IPQ5018-specific QCN6122 (2x2) solution or by the more generally
available PCIe-based QCN9074 (4x4) wifi chip.
On IPQ5018/QCN6122-based boards, both QCN6122 and IPQ5018 wifi is
initialized by IPQ5018 firmware which comes in different versions:
- IPQ5018: firmware files to initialize WCSS and the internal wifi chip
- IPQ5018/QCN6122: above + additional firmware segments to initialize
the QCN6122 chip incl. (de-)assertion of resets and clocks enablement
OpenWrt currently packages the combined IPQ5018/QCN6122 firmware for
both architectures. As such, let's switch to using IPQ5018-only firmware
for boards not packed with QCN6122 chip(s) and keep using the shared
firmware for devices that do have QCN6122(s) chips.
This helps us move to using upstreamed IPQ5018 firmware while using the
legacy repo for IPQ5018/QCN6122 firmware and rule out any initialization
conflicts/issues caused by loading QCN6122 on IPQ5018-only boards.
While at it, default to the secure WCSS remoteproc driver sent upstream
for review, move QCN6122 wifi nodes to a separate dtsi, override the Q6
node to load the multi-PD-based architecture remoteproc driver for
needed only by IPQ5018/QCN6122 designs, reference said dtsi in
boards packed with QCN6122 wifi chip(s), and add provision for migrating
the radio path as the wifi nodes now adhere to linux device tree naming
conventions.
Signed-off-by: George Moussalem <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20928
Signed-off-by: Robert Marko <[email protected]>
George Moussalem [Thu, 23 Oct 2025 11:07:09 +0000 (15:07 +0400)]
qualcommax: Add support for qcom remoteproc WCSS secure PIL driver
Add support for qcom remoteproc WCSS secure PIL driver.
Signed-off-by: George Moussalem <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20928
Signed-off-by: Robert Marko <[email protected]>
Rani Hod [Thu, 27 Nov 2025 23:43:13 +0000 (01:43 +0200)]
siflower: sf21 device tree fix
`i2c1` node was missing `resets`, so even when enabled, the driver would
not recognize it:
```
i2c_designware
c101000.i2c: Unknown Synopsys component type: 0x00000000
```
With this fix, I2C pins on BPi-RV2 26-pin GPIO header are usable.
Signed-off-by: Rani Hod <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20969
Signed-off-by: Christian Marangi <[email protected]>
Goetz Goerisch [Thu, 27 Nov 2025 14:08:21 +0000 (15:08 +0100)]
odhcpd: update to Git HEAD (2025-11-27)
4246bbda56d6 dhcpv4: improve pool var naming
407789e5f307 odhcpd: rename union if_addr -> in46_addr
66e7739f7c86 odhcpd: rename prefix -> prefix_len
75dfe0e71050 odhcpd: rename iface->addr4 -> iface->oaddrs4
d619b5ae28a4 dhcpv4: fix no_dynamic_dhcp
e8022eebc8a7 netlink: variable naming cleanup
fca3fee38ea4 netlink: add netmask for IPv4
1c2e8b60809a dhcpv4: simplify pool determination
558fb499c8c2 dhcpv4: rename iface->dhcpv4_local -> iface->dhcpv4_own_ip
ab8b1572247d dhcpv4: remove iface->dhcpv4_mask
af0c94063e66 dhcpv4: remove iface->dhcpv4_bcast
83055f636091 odhcpd: consistent dns naming
0a54ce0d2b57 odhcpd: rename iface->search -> iface->dns_search
a05cc991716c dhcpv4: iface->dhcpv4_router -> iface->dhcpv4_routers
b4ab371c541a config: fix (S)NTP realloc handling
adb2b8a1afff config: fix realloc() handling for the "upstream" option
38b0920e376b config: fix realloc() error handling for "dhcpv6_raw" option
2e1042c6c07f config: handle realloc failure in piofolder parsing
b9db4d7061a0 dhcpv6: handle realloc failure
ae9e22ab3fad netlink: make it clearer that we're handling realloc correctly
d21e504b38ab dhcpv6-ia: fix realloc bug
https://github.com/openwrt/odhcpd/compare/
650a5df88eba...
d21e504b38ab
Signed-off-by: Goetz Goerisch <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20958
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Rosen Penev [Wed, 4 Sep 2024 00:07:49 +0000 (17:07 -0700)]
lantiq: more conversions to nvmem
Now that NVMEM in UBI is supported, more handling can be moved.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Wed, 4 Sep 2024 00:07:49 +0000 (17:07 -0700)]
lantiq: dgn3500: use nvmem to load calibration
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Thu, 23 Oct 2025 20:19:41 +0000 (13:19 -0700)]
lantiq: homehub-v3a: assign wlan mac in dts
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Thu, 27 Nov 2025 01:04:11 +0000 (17:04 -0800)]
kernel: disable non layout u-boot,env
All users of regular CONFIG_NVMEM_U_BOOOT_ENV have been converted to use
layouts.
CONFIG_NVMEM_U_BOOT_ENV selects the layout variant anyway so this is
safe to do.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <[email protected]>
Rosen Penev [Thu, 27 Nov 2025 00:55:49 +0000 (16:55 -0800)]
treewide: convert u-boot,env to nvmem-layout
Non nvmem-layout is deprecated.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <[email protected]>
Raylynn Knight [Tue, 25 Nov 2025 23:39:18 +0000 (18:39 -0500)]
mpc85xx: HPE MSM460 add HPE MSM466 alias
Define MSM466 as alternative name, to explicitly show the device is
supported using existing image (MSM460). The only difference between
the MSM460 and MSM466 is that the MSM466 has external antenna.
Signed-off-by: Raylynn Knight <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20937
Signed-off-by: Hauke Mehrtens <[email protected]>
Thomas Richard [Tue, 18 Nov 2025 12:33:48 +0000 (13:33 +0100)]
arm-trusted-firmware-stm32: bump to v2.13
Since version 4.8.0, OPTEE handles correctly RTC clock configuration for
STM32MP15 based boards. So the patch can be dropped.
Signed-off-by: Thomas Richard <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20953
Signed-off-by: Hauke Mehrtens <[email protected]>
Thomas Richard [Tue, 18 Nov 2025 12:32:28 +0000 (13:32 +0100)]
optee-os-stm32: bump to 4.8.0
Bump optee-os-stm32 to upstream release 4.8.0.
Signed-off-by: Thomas Richard <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20953
Signed-off-by: Hauke Mehrtens <[email protected]>
Thomas Richard [Mon, 13 Oct 2025 12:08:58 +0000 (14:08 +0200)]
uboot-stm32: bump to 2025.10
Bump uboot-stm32 to upstream release 2025.10 and remove upstreamed patch.
Signed-off-by: Thomas Richard <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20953
Signed-off-by: Hauke Mehrtens <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 19:26:37 +0000 (20:26 +0100)]
kernel: move .quilt_used to quilt.mk
Move .quilt_used from kernel-defaults.mk to quilt.mk.
This is done to be consistent with the parallel Build/Patch/Default and
Host/Patch/Default and permit better Quilt handling on any package that
might use Kernel/Patch/Default.
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 19:24:05 +0000 (20:24 +0100)]
Revert "kernel: move .quilt_used to quilt.mk"
This reverts commit
61bfcc4bd74ffde1c400d4649724f262aa081e7b.
The change was wrong as it was placed on the wrong define section.
Signed-off-by: Christian Marangi <[email protected]>
Anari Jalakas [Thu, 27 Nov 2025 13:22:03 +0000 (15:22 +0200)]
config: add !USE_APK dependency to CLEAN_IPKG
When USE_APK is enabled, APK replaces opkg/ipkg, leading to a build
failure when CLEAN_IPKG is also selected. Add 'depends on !USE_APK' to
CLEAN_IPKG to ensure this option is only selectable when opkg/ipkg is
the active package manager.
Signed-off-by: Anari Jalakas <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20957
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 13:23:56 +0000 (14:23 +0100)]
bpf-headers: update to version 6.12
Update bpf-headers to version 6.12 now that we target kernel version
6.12.
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 13:26:33 +0000 (14:26 +0100)]
bpf-headers: correctly support refreshing the package
Overwrite default Quilt/Refresh/Package and use the Kernel variant to
correctly refresh bpf-headers patches.
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 13:18:50 +0000 (14:18 +0100)]
kernel: move .quilt_used to quilt.mk
Move .quilt_used from kernel-defaults.mk to quilt.mk.
This is done to be consistent with the parallel Build/Patch/Default and
Host/Patch/Default and permit better Quilt handling on any package that
might use Kernel/Patch/Default.
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 12:39:57 +0000 (13:39 +0100)]
libtraceevent: switch to meson and add missing dep for libtraceevent-extra
Switch to Meson build system and add missing dependency for
libtraceevent-extra.
This switch indirectly fix a compilation error on 32bit target that
weren't getting correct target CFlags. Using Meson fix honour our CFlags
and fix the compilation error.
Signed-off-by: Christian Marangi <[email protected]>
Shiji Yang [Thu, 27 Nov 2025 09:39:05 +0000 (17:39 +0800)]
generic: add missing symbol ARM64_CONTPTE
Add the missing symbol to fix build halt on aarch64 targets:
```
Contiguous PTE mappings for user memory (ARM64_CONTPTE) [Y/n/?] (NEW) make[7]: *** [scripts/kconfig/Makefile:85: syncconfig] Error 1
make[6]: *** [Makefile:686: syncconfig] Error 2
```
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20954
Signed-off-by: Christian Marangi <[email protected]>
Nick Hainke [Thu, 27 Nov 2025 10:22:58 +0000 (11:22 +0100)]
selinux-policy: update to 2.8.4
Changelog:
73e77ae odhcpd anticipate per link configuration
c353698 various
8465968 iwinfo: ucode
9d9f12c various
2f41f9b various
70bb8bc various loose ends
6e817d4 netifd odhcpd wifi
69558b8 addresses various surfaced policy issues
9eb2dae README update
0a710e3 README
6fffaf6 pidfs: fsuse task seclabelfs
b051c6d makefile reproducible
Link: https://github.com/openwrt/openwrt/pull/20955
Signed-off-by: Nick Hainke <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 11:47:33 +0000 (12:47 +0100)]
ethtool: drop dependency on kernel 6.6
Since now we default to 6.12 and we dropped any support for kernel 6.6,
drop any dependency on it.
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 11:47:16 +0000 (12:47 +0100)]
kselftests-bpf: drop dependency on kernel 6.6
Since now we default to 6.12 and we dropped any support for kernel 6.6,
drop any dependency on it.
Signed-off-by: Christian Marangi <[email protected]>
Christian Marangi [Thu, 27 Nov 2025 11:46:37 +0000 (12:46 +0100)]
config: drop dependency on kernel 6.6
Since now we default to 6.12 and we dropped any support for kernel 6.6,
drop any dependency on it.
Signed-off-by: Christian Marangi <[email protected]>
Shiji Yang [Wed, 26 Nov 2025 16:04:35 +0000 (00:04 +0800)]
treewide: dts: remove {#address,#size}-cells from "spi-nand" compatible node
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <[email protected]>
Shiji Yang [Wed, 26 Nov 2025 15:49:55 +0000 (23:49 +0800)]
treewide: dts: remove {#address,#size}-cells from "jedec,spi-nor" compatible node
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <[email protected]>
Shiji Yang [Wed, 26 Nov 2025 15:06:55 +0000 (23:06 +0800)]
kernel: of: avoid some unnecessary bad cell count warnings
This patchset silences some noisy dts false warnings:
[ 0.616266] OF: Bad cell count for /spi@
1100d000/flash@0/partitions
[ 0.622551] OF: Bad cell count for /spi@
1100d000/flash@0/partitions
Closes: https://github.com/openwrt/openwrt/issues/14701
Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <[email protected]>
Mieczyslaw Nalewaj [Wed, 26 Nov 2025 17:18:46 +0000 (18:18 +0100)]
packages: remove dependencies for kernel 6.6 and 6.12
Once kernel 6.6 support ends, its dependencies will become redundant.
Remove them and keep only those for kernel 6.12.
Signed-off-by: Mieczyslaw Nalewaj <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20943
Signed-off-by: Christian Marangi <[email protected]>
Mieczyslaw Nalewaj [Wed, 26 Nov 2025 16:26:32 +0000 (17:26 +0100)]
treewide: drop Linux 6.6 patches, hacks, configs and conditional
Drop all kernel 6.6 patches, hacks, backports and configuration support,
and remove the CONFIG_LINUX_6_6 guarded conditional in filogic.mk.
Signed-off-by: Mieczyslaw Nalewaj <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20943
Signed-off-by: Christian Marangi <[email protected]>
Rosen Penev [Fri, 24 Oct 2025 03:21:30 +0000 (20:21 -0700)]
lantiq: match wifi node names to reg
node name matches various comments about the pci path.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20522
Signed-off-by: Hauke Mehrtens <[email protected]>
Nick Hainke [Sun, 23 Nov 2025 17:05:51 +0000 (18:05 +0100)]
libsemanage: update to 3.9
Release Notes:
https://github.com/SELinuxProject/selinux/wiki/Releases#release-39
Remove upstreamed:
- 0001-libsemanage-create-semanage_basename-to-ensure-posix.patch
Link: https://github.com/openwrt/openwrt/pull/20908
Signed-off-by: Nick Hainke <[email protected]>
Nick Hainke [Sun, 23 Nov 2025 17:07:03 +0000 (18:07 +0100)]
libselinux: update to 3.9
Release Notes:
https://github.com/SELinuxProject/selinux/wiki/Releases#release-39
Remove upstreamed:
- 0001-Inject-matchpathcon_filespec_add64-if-defined-__INO_.patch
-> https://github.com/SELinuxProject/selinux/commit/
5c3fcbd931b7f9752b5ce29cec3b6813991d61c0
- 100-v2-libselinux-be-careful-with-non-portable-LFS-macro.patch
-> https://github.com/SELinuxProject/selinux/commit/
21dd00713ae99b13e36c632992cb171c6ec1abce
Link: https://github.com/openwrt/openwrt/pull/20908
Signed-off-by: Nick Hainke <[email protected]>
Nick Hainke [Sun, 23 Nov 2025 17:04:20 +0000 (18:04 +0100)]
libsepol: update to 3.9
Release Notes:
https://github.com/SELinuxProject/selinux/wiki/Releases#release-39
Link: https://github.com/openwrt/openwrt/pull/20908
Signed-off-by: Nick Hainke <[email protected]>
Nick Hainke [Sun, 23 Nov 2025 17:03:13 +0000 (18:03 +0100)]
secilc: update to 3.9
Release Notes:
https://github.com/SELinuxProject/selinux/wiki/Releases#release-39
Link: https://github.com/openwrt/openwrt/pull/20908
Signed-off-by: Nick Hainke <[email protected]>
Nick Hainke [Sun, 23 Nov 2025 16:20:26 +0000 (17:20 +0100)]
policycoreutils: update to 3.9
Release Notes:
https://github.com/SELinuxProject/selinux/wiki/Releases#release-39
Remove upstreamed patch:
- 0001-policycoreutils-run_init-define-_GNU_SOURCE.patch
Link: https://github.com/openwrt/openwrt/pull/20908
Signed-off-by: Nick Hainke <[email protected]>
Nick Hainke [Sun, 23 Nov 2025 16:13:42 +0000 (17:13 +0100)]
checkpolicy: update to 3.9
Release Notes:
https://github.com/SELinuxProject/selinux/wiki/Releases#release-39
Link: https://github.com/openwrt/openwrt/pull/20908
Signed-off-by: Nick Hainke <[email protected]>
Hauke Mehrtens [Wed, 26 Nov 2025 20:24:31 +0000 (21:24 +0100)]
lantiq: Fix build of xway target
The kernel update commit also changed the name of the dtsi node. Adapt
the other dts files.
Fixes: 738876e76bb2 ("kernel: bump 6.12 to 6.12.58")
Signed-off-by: Hauke Mehrtens <[email protected]>
Stijn Tintel [Wed, 26 Nov 2025 19:06:28 +0000 (21:06 +0200)]
kernel: drop CONFIG_ARM64_CONTPTE from target configs
This is no longer needed after the previous commit.
Signed-off-by: Stijn Tintel <[email protected]>
Stijn Tintel [Wed, 26 Nov 2025 18:55:40 +0000 (20:55 +0200)]
kernel: fix dependency on non-existent symbol
KERNEL_ARM64_CONTPTE depends on KERNEL_ARM64 which does not exist. Fix
it by depending on aarch64 instead.
Fixes: e9799d2dd4b0 ("kernel: add KERNEL_ARM64_CONTPTE")
Signed-off-by: Stijn Tintel <[email protected]>
Goetz Goerisch [Mon, 24 Nov 2025 07:56:28 +0000 (08:56 +0100)]
odhcpd: update to Git HEAD (2025-11-23)
8a8bb3c1a673 src: consolidate and improve fallthrough
8ffe79e3f086 src: improve attributes
0a4d4e11c91c odhcpd: simplify signal handling
6af938921628 odhcpd: make ubus optional at runtime
7313ba262b76 odhcpd: update devel-build.sh
038a7bbfc30d dhcpv4: simplify random address selection
8c574bd2fe62 dhcpv6: prevent network loop scenario
76b2d00ee5f0 router: Modify relayed RA PIO L and RA M/O flags according to interface policy
d236b2e0c53e github: ci: add MIPS64, PowerPC64 and RISCV64
d1500bb5d64d all: implement RFC8910 captive portal (CP) option
9830e5e2bf37 all: implement RFC8910 captive portal (CP) option for DHCPv4
9b9ea96ca90e statefiles: fix off-by-one-bug
c10784ece29c dhcpv4: replace ToS precedence
24f013500691 dhcvp4: use tmp fd in dhcpv4_setup_interface()
3c32b27d8bab dhcpv4: simplify error handling in dhcpv4_setup_interface()
5b7cfef774fb dhcpv4: define val where it is used in dhcpv4_setup_interface()
b0739f23c310 dhcpv4: add BPF to dhcpv4_setup_interface()
650a5df88eba ndp: correctness fix for BPF filter
Signed-off-by: Goetz Goerisch <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20919
[add myself as maintainer]
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Goetz Goerisch [Sun, 23 Nov 2025 09:05:10 +0000 (10:05 +0100)]
qoriq: drop support for kernel 6.6
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20889
Signed-off-by: Stijn Tintel <[email protected]>
projects / openwrt / openwrt.git / log