realtek: dsa: Record number of supported MSTs

Each SoC supports a different number of MST(I)s. The code must know this
limitation to correctly reject unsupported MSTIs or to allocate a large
enough mapping table.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20421
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: rtl93xx: Implement vlan fast age flushing

The DSA port code is trying to flush associated VLANs whenever the MST
state is changed. This functionality is available on a per port+vid based
using the L2_TBL_FLUSH_CTRL which is already used for the .port_fast_age
callbacks.

Signed-off-by: Issam Hamdi <[email protected]>
Co-developed-by: Sven Eckelmann <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20421
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: rtl93xx: Switch to MSTP compatible STP mode

The realtek DSA switch driver sets up all VLANs using CIST. It is therefore
not necessary to enforce CIST using the ST_CTRL register.

This allows us later to overwrite the MSTI of VLANs. This is necessary to
get MSTP working on RTL93xx.

Signed-off-by: Issam Hamdi <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20421
Signed-off-by: Hauke Mehrtens <[email protected]>

download: use reasonable timeout and retry parameters

Set a timeout of 5 seconds and 3 retries to reduce the time it takes for connection timeout.

Signed-off-by: Andy Chiang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19977
Signed-off-by: Hauke Mehrtens <[email protected]>

ipq40xx: Add support for Linksys MR6350

This pull request is based on
- the discussions in https://forum.openwrt.org/t/adding-openwrt-support-for-linksys-mr6350
- https://github.com/openwrt/openwrt/pull/11405 which added support for similar devices.

Device Specs:
- IPQ4019
- Quad Core CPU
- 256 MB RAM
- 256 MB FLASH
- 4 LAN ports, 1 WAN port
- 2.4GHz (802.11n) and 5GHz (802.11c) wifi
- 3 LEDs (Red, blue, green) which are routed to one indicator at the top of the case
- 2 buttons (Reset, WPS)

Disassembling the device:
- There are 4 screws at the bottom of the device which must be removed
- Two are under the fron rubber feets
- Two are under the labels in the back (corner next to the rear rubber feets)

Serial interface:
- The serial interface is already populated on the device with a 6-pin header
- Pin 1 is next to the heatsink
- Pinout: 1: 3.3V, 2: TX, 3: RX, 4: unknown, 5: GND, 6: GND
- Settings: 115200, 8N1

Migrating to OpenWrt requires multiple steps:
- Load and boot the initramfs image
- Adapt U-Boot settings to support bigger kernels
- Flash the sysupgrade image

Load and boot initramfs:
- Connect serial interface
- Set up a TFTP server on IP 192.168.1.254
- Copy openwrt-ipq40xx-generic-linksys_mr6350-initramfs-zImage.itb to TFTP server
- Rename file to C0A80101.img
- Boot up the device and stop in U-Boot
- Run the following U-Boot commands after a link has been established:
  tftp
  bootm
- Initramfs image is started now.

Adapt U-Boot settings to support bigger kernels:
- Run "fw_printenv" in the initramfs image  after booting
- There should be an entry kernsize=300000 which indicates the maximum size for the kernel is 3MB
- Execute "fw_setenv kernsize 500000" to increase the max kernel size to 5MB
- Check that the change are applied with "fw_printenv"

Flash the sysupgrade image:
- Default sysupgrade routine either with a initramfs image containing LuCI or via command line.

Revert back to OEM firmware:
- Only tested with FW_MR6350_1.1.3.210129_prod.img
- Flash the OEM firmware via sysupgrade
- Forced update is required

Signed-off-by: Roland Reinl <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/17977
Signed-off-by: Robert Marko <[email protected]>

ipq40xx: add support for Netgear RBS20

This device has only half the flash and ram of the RBR20. It also has
two lan ports instead of wan and lan.

Hardware
--------
SOC:    Qualcomm IPQ4019
FLASH:  128MB (Winbond W29N01HVSINF)
RAM:    256MB (Winbond W632GU6MB-12)
WIFI:   Qualcomm IPQ4019
        Qualcomm Atheros QCA9886
ETH:    2x LAN
LED:    5 (4 RGB at top, 1 RG at back)
BTN:    WPS, Reset
UART:   115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND

MAC addresses
-------------
LAN     Label MAC (stored in boarddata1 offset 0x0)
2.4G    LAN
5GLow   LAN + 3 (stored in boarddata1 offset 0xc)
5GUpper LAN + 2 (stored in boarddata1 offset 0x12)

Installation
------------
Either use the vendor ui upgrade method or nmrpflash to install the
factory image.

Signed-off-by: Christoph Krapp <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20560
Signed-off-by: Robert Marko <[email protected]>

ipq40xx: add support for Netgear RBR20

This device shares a lot of similarities with the LBR20 - the RBR20 just
misses the LTE modem and its formfactor is alot smaller. Other than that
the LED configuration matches other RBR devices but the RBR20 has less
LEDs than its larger counterparts.

Hardware
--------
SOC:    Qualcomm IPQ4019
FLASH: 256MB (Winbond W29N02GVSIAF)
RAM:   512MB (Nanya NT5CC256M16EP-EK)
WIFI:   Qualcomm IPQ4019
        Qualcomm Atheros QCA9886
ETH: 1x WAN, 1x LAN
LED: 5 (4 RGB at top, 1 RG at back)
BTN: WPS, Reset
UART: 115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND

MAC addresses
-------------
LAN Label MAC (stored in boarddata1 offset 0x0)
WAN LAN + 1 (stored in boarddata1 offset 0x6)
2.4G LAN
5GLow LAN + 3 (stored in boarddata1 offset 0xc)
5GUpper LAN + 2 (stored in boarddata1 offset 0x12)

Installation
------------
Either use the vendor ui upgrade method or nmrpflash to install the
factory image.

Signed-off-by: Christoph Krapp <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20560
Signed-off-by: Robert Marko <[email protected]>

ipq-wifi: update to Git HEAD (2025-11-15)

fa62f8a2885c ipq8074: add BDF for Zyxel NWA210AX
7c6b7545f69a qca4019: qca9888: add bdfs for Netgear RBK20

Signed-off-by: Robert Marko <[email protected]>

realtek: dsa: rtl93xx: Configure default QoS prioritization

RTL838x+RTL839x both configure a default QoS behavior with a default
mapping. This also needs to be added to RTL93xx to ensure a consistent
behavior:

* Set the default mapping between DSCP and priority: prio = dscp >> 3.
* Set the default mapping between internal priority and queues
* Set uniform prioritization of queues (as with other SoCs)

Signed-off-by: Issam Hamdi <[email protected]>
Co-developed-by: Sven Eckelmann <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20640
Signed-off-by: Robert Marko <[email protected]>

realtek: rtl93xx: Send per port packets on physical port

If link aggregation with LACP is activated, we must send out the LACP
packets on the physical port and not on a logic port. Otherwise, the per
port packets might be (rebalanced) between the different ports in a link
aggregation group.

Such rebalancing breaks 802.3ad and will leave ports in a churned state.

Fixes: 8c42e63a69f6 ("realtek: rtl93xx: fix incorrect destination port selection")
Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20728
Signed-off-by: Robert Marko <[email protected]>

realtek: dsa: Add non-primary LAG ports to port matrix

If ports of a RTL93xx switch are not added to a port matrix then they are
not used for the link aggregation. As result, communication will then just
break on non-primary interfaces.

This can be reproduced in balanced-xor and 802.3ad bandwidth mode.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20729
Signed-off-by: Robert Marko <[email protected]>

realtek: pcs: rtl93xx: fix SerDes polarity configuration for RTL931X

Commit 56e9a73d0b added support for configuring the SerDes polarity for
both RTL930X and RTL931X. Based on the code in the Realtek SDK in [1]
and [2], in both cases the same register bits are set. Thus, a common
implementation was provided which worked with e.g. USXGMII or 10GBase-R
configured SerDes.

However, after further tests, a strange issue occured where it didn't
work that well for all SerDes configurations. While running fine for
10GBase-R links on two adjacent SerDes, it didn't for 1000Base-X links
on one of two adjacent SerDes with the link not being detected as a
symptom.

Diving into the SDK again revealed that the referenced implementation of
polarity configuration is (by accident or by purpose) misleading. While
[1] and [3] for RTL930X match, [2] and [4] for RTL931X actually don't.
[4] writes the bits for the 1G polarity setting on different background
SerDes, thus in another frontend page.

Split implementations for RTL930X and RTL931X again and adjust the one
for RTL931X according to [4]. This resolves the issues with 1000Base-X
behavior.

[1] https://github.com/plappermaul/realtek-doc/blob/69d2890a2e2d7a03df6e40e2cd2c32ff5b074dcf/sources/rtk-xgs1210/src/hal/phy/phy_rtl9300.c#L1384
[2] https://github.com/plappermaul/realtek-doc/blob/69d2890a2e2d7a03df6e40e2cd2c32ff5b074dcf/sources/rtk-xgs1210/src/hal/phy/phy_rtl9310.c#L3479
[3] https://github.com/plappermaul/realtek-doc/blob/69d2890a2e2d7a03df6e40e2cd2c32ff5b074dcf/sources/rtk-xgs1210/src/dal/longan/dal_longan_construct.c#L2246
[4] https://github.com/plappermaul/realtek-doc/blob/69d2890a2e2d7a03df6e40e2cd2c32ff5b074dcf/sources/rtk-xgs1210/src/dal/mango/dal_mango_construct.c#L1550

Fixes: 56e9a73d0b ("realtek: pcs: rtl93xx: provide proper SerDes polarity
configuration")
Signed-off-by: Jonas Jelonek <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20767
Signed-off-by: Robert Marko <[email protected]>

ath79: fix MAC addresses on MikroTik RB962UiGS-5HacT2HnT

The MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) currently comes up
with random MAC addresses. Assign the MAC addresses from hard_config for
LAN and WAN ports.

Fixes: c2140e32ce ("ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)")
Signed-off-by: Daniel Golle <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20782
Signed-off-by: Robert Marko <[email protected]>

wifi-scripts: ucode: create wpa_psk_file and sae_password_file when needed

This handles the case when 'wpad' or 'wpad-mini' package is used which is
missing WPA3 support. This makes it impossible to use ucode wifi-scripts
on such APs as it will raise an error:

   daemon.err hostapd: Line 87: unknown configuration item 'sae_password_file'

This also achieves parity with what is currently happening with old wifi-scripts.
The behavior now matches.

Fixes: https://github.com/openwrt/openwrt/issues/20781
Signed-off-by: Rany Hany <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20784
Signed-off-by: Robert Marko <[email protected]>

libubox: update to Git HEAD (2025-11-14)

a75209f62982 blobmsg: refactor blobmsg_cast_u64/s64
97d1839295e5 github: ci: minor fixes
e8dafede37fc github: ci: add powerpc arch
c1f0024fb052 github: ci: add cmake build and source directories
4dd874d2b412 github: ci: tests: rename test step
7686b12d11ba github: ci: tests: add build/bin to path
be21d12b2bed github: ci: disable json-c tests
af438ba0705f scripts: devel-build: disable json-c tests
240d2d5ef58b tests: shunit2: add test for _jshn_append leading space fix
82cb5fd66af9 libubox: Drop extraneous space when appending values to variable
17143f94dcbf libubox: add a simple build script
5b11fb18dc05 github: ci: add tests

https://github.com/openwrt/libubox/compare/e357be611cd9...a75209f62982

Signed-off-by: Álvaro Fernández Rojas <[email protected]>

mediatek: add mt7987-2p5g-phy-firmware to MT7987 devices

Add mt7987-2p5g-phy-firmware to DEVICES_PACKAGES of the MT7987A RFB as
well as the BananaPi R4 Lite.

Signed-off-by: Daniel Golle <[email protected]>

linux-firmware: package mt7987-2p5g-phy-firmware

Package firmware for the built-in 2.5G PHY of the MediaTek MT7987 SoC.

Signed-off-by: Daniel Golle <[email protected]>

linux-firmware: update to 20251111

$ git log --no-merges --pretty=oneline --abbrev-commit  20251021..20251111
fcf22f50 rtl_bt: Update RTL8922A BT USB firmware to 0x41C0_C905
c0af6c70 linux-firmware: add firmware for mt7987 internal 2.5G ethernet phy
a50c068b rtw88: 8822b: Update firmware to v30.20.0
e5606bd7 rtl_nic: add firmware rtl8125k-1
c5831f31 ASoC: tas2781: Update dsp firmware for HP and ASUS projects
ad907cca Revert "Merge branch 'robot/patch-0-1762671757' into 'main'"
d665e29c ASoC: tas2781: Update dsp firmware for HP and ASUS projects
213080ae amdgpu: DMCUB updates for various ASICs
23cf7dbb amdgpu: DMCUB updates for various ASICs
95cd295e qcom: add SOCCP firmware for kaanapali platform
9444af1a xe: Update GUC to v70.53.0 for BMG, LNL, PTL
f2a23165 i915: Update GUC to v70.53.0 for DG2, MTL
4dedd6cb rtw89: 8851b: update fw to v0.29.41.5
84cc37f3 rtw89: 8852b: update fw to v0.29.128.0 with format suffix -2
3ab5b9e5 rtw89: 8852b: update fw to v0.29.29.14
1b1c14bb Revert "rtw89: 8852b: update fw to v0.29.128.0"
9a0d0ed6 rtw89: 8852bt: update fw to v0.29.127.0 with format suffix -1
be71e790 rtw89: 8852bt: update fw to v0.29.122.1
b6252a03 Revert "rtw89: 8852bt: update fw to v0.29.127.0"
a976b0aa linux-firmware: Update firmware file for Intel BlazarU core
5a689a2f linux-firmware: Update firmware file for Intel BlazarI core
77425784 linux-firmware: Create audio folder in ti folder, and move all the audio firmwares into it
e189b618 amdgpu: DMCUB updates for various ASICs
646d97f5 linux-firmware: Update WHENCE for microcode_amd_fam19h.bin
e637542f linux-firmware: Update AMD cpu microcode
0fc31ad6 linux-firmware: update firmware for MT7925 WiFi device
b63c322f mediatek MT7925: update bluetooth firmware to 20251015213201
35e54243 rtl_bt: Add firmware and config files for RTL8761CUV
ad915447 linux-firmware: Update AMD cpu microcode
7bcedf5c qcom: add ADSP firmware for kaanapali platform
728e9243 amdgpu: DMCUB updates for various ASICs
05105d24 linux-firmware: Renaming the file to cover a wide range of HP Lunar Lake system.
b582532d mediatek MT7920: update bluetooth firmware to 20251020151255
33d0511d linux-firmware: update firmware for MT7922 WiFi device
c2087f88 linux-firmware: update firmware for MT7920 WiFi device
3a49a735 amd-ucode: Fix minimum revisions in README
0de0cd7f cirrus: cs35l41: Rename various Asus Laptop firmware files to not have Speaker ID
93c92978 mediatek MT7922: update bluetooth firmware to 20251020143443

Signed-off-by: Daniel Golle <[email protected]>

kernel: mtk_eth_soc: fix encapsulation check for GSO fraglist packets

Use skb->encapsulation flag instead of skb_tnl_header_len() to detect
encapsulated packets. Prevents false positives on non-encapsulated packets.

Reported-by: Mason-cw Chang (張哲維) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

wifi-scripts: respect rsn_override=0 in mixed modes

Only set rsn_override_key_mgmt when rsn_override is enabled.

Reported-by: Michael-cy Lee (李峻宇) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

wifi-scripts: only enable RSN override when parameters differ

When encryption is set to 'sae' without explicit pairwise cipher in
non-HE/EHT mode, both the main RSNE and override RSNE would advertise
identical parameters (SAE+CCMP+MFP=2), adding unnecessary overhead.

Check that the pairwise ciphers differ before enabling override. This
preserves the intended behavior for HE/EHT modes (GCMP-256+CCMP vs CCMP)
while avoiding pointless override IEs.

Reported-by: Michael-cy Lee (李峻宇) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

hostapd: fix phy parameter in iface_update_supplicant_macaddr

The function was using phydev.name (e.g., "phy0.0") instead of
phydev.phy (e.g., "phy0") when calling wpa_supplicant.phy_set_macaddr_list.
This is inconsistent with all other wpa_supplicant ubus calls in the same
file which correctly use phydev.phy.

Reported-by: Michael-cy Lee (李峻宇) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

wifi-scripts: fix MLO AP setup with disabled radios

When an MLO interface specifies multiple radios and the first radio
is disabled, the MLO configuration was never created because the code
only attempted to create it when processing the first device in the
list (which gets skipped if disabled).

Fix by creating the MLO config for the first enabled device instead
of only when processing dev_names[0].

Reported-by: Michael-cy Lee (李峻宇) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

wpa_supplicant: fix MAC address assignment for MLD interfaces

Assign the address at wdev create time, similar to legacy interfaces.

Reported-by: Michael-cy Lee (李峻宇) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

wifi-scripts: fix wds client mode with MLO

Ensure that the 4addr flag is passed to phy.wdev_add.

Reported-by: Michael-cy Lee (李峻宇) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

mpc85xx: make kernel 6.12 the default kernel

Signed-off-by: David Bauer <[email protected]>

mpc85xx: kernel: 6.12: fix issue with ifc nodes in P1010

In upstream [0] ifc node compatible was changed and it broke ifc at all.
Rosen Penev send revert commit to upstream [1] which repair it.

This patch add this pending patch to mpc85xx.

[0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0bf51cc9e9e57a751b4c5dacbfa499ba5cd8bd72
[1] https://patchwork.ozlabs.org/project/linuxppc-dev/patch/20251105205524[email protected]/

Signed-off-by: Pawel Dembicki <[email protected]>

mpc85xx: introduce 6.12 testing kernel

Signed-off-by: David Bauer <[email protected]>

mpc85xx: refresh kernel config

Signed-off-by: David Bauer <[email protected]>

mpc85xx: use strscpy instead of strlcpy

Usage of strlcpy results in a compilation error. strscpy is preferred
anyways and equivalent for our case.

Signed-off-by: David Bauer <[email protected]>

mpc85xx: refresh kernel 6.12 patches

Signed-off-by: David Bauer <[email protected]>

kernel/mpc85xx: Restore kernel files for v6.6

This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Pawel Dembicki <[email protected]>

kernel/mpc85xx: Create kernel files for v6.12 (from v6.6)

This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Pawel Dembicki <[email protected]>

qualcommax: ipq50xx: Add support for CMCC PZ-L8

CMCC PZ-L8 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ5000.

Specifications:
- SoC : Qualcomm IPQ5000
- RAM : Integrated 256MiB DDR3L
- Flash : 128 MiB SPI-NAND (ESMT F50D1G41LB)
- WLAN : 2.4/5 GHz 2T2R
-  2.4 GHz : Qualcomm IPQ5000 (SoC)
-  5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 4x 10/100/1000 Mbps
-  switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 2x LEDs, 2x Keys
- UART : Through-hole on PCB, 4pins in the middle of the black aluminum heat sink
-  assignment : 3.3V, GND,TX, RX (from left to right)
-  settings : 115200n8
- Power : 12 VDC, 1 A

Flashing Instructions:
1. SSH Method
(1) Enable SSH on the stock firmware
a. Version 501.8 and 501.9:
Log in to http://192.168.10.1 with the password on the sticker
Append "/admin/system/admin" to the URL and press Enter
Delete "Dropbear instance", click "Add instance", then "Save and Apply"
Reboot the router

b. Version 501.11 and 501.12:
While the router is running the stock firmware, press and hold the reset button for 20-30 seconds
Open http://192.168.10.1:56781 and login with username "root" and the password on the sticker
Run "vi /etc/config/dropbear" and delete the line "option enable '0'"
Reboot the router

(2) Upload the factory.ubi file to router's /tmp directory (using scp or wget)
and execute the following commands in the router's shell

export rootfs=$(cat /proc/mtd | grep rootfs | grep -v _ | cut -d: -f1)
ubidetach -f -p /dev/${rootfs}
ubiformat /dev/${rootfs} -y -f /tmp/factory.ubi

2. U-Boot Method using UBI Image
Place the factory.ubi file on your TFTP server, enter U-Boot CLI and exec these commands

tftpboot <your_tftp_server_ip>:factory.ubi
flash rootfs
reset

3. U-Boot Method using initramfs Image
(1) Place the openwrt-*-initramfs-fit-uImage.itb file on your TFTP server
and rename it to initramfs.bin
(2) Enable serial console, enter to U-Boot CLI and exec these commands

tftpboot <your_tftp_server_ip>:initramfs.bin
bootm

(3) Once boot completed, upload the sysupgrade.bin file to router's /tmp directory
(using scp or wget) and execute the following command in openwrt shell

sysupgrade -n /tmp/sysupgrade.bin

Switching to the Stock Firmware:
Please follow the commit https://github.com/openwrt/openwrt/commit/3b7d72bc2ecca2f962319b0a4fb9beb7609a0222

Partition Layout (Stock Firmware):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000004300000 : "rootfs"
0x000004300000-0x000007d00000 : "rootfs_1"

Notes:
This device is almost the same as ELECOM WRC-X3000GS2, including partition layout and the dual-boot feature.

Known Issues:
- All Wi-Fi related peripherals are disabled in device tree, since 256 MiB RAM is too few for ath11k.
- This device has another version with nand flash FM25SL01, which is not supported at the moment.
  https://github.com/immortalwrt/immortalwrt/blob/master/target/linux/mediatek/patches-6.12/342-mtd-spinand-Support-fmsh.patch

MAC Addresses:
Interface MAC Address Location (binary)
LAN A4:39:B6:xx:xx:9D (0:ART, 0x00-0x05)
WAN A4:39:B6:xx:xx:9E (0:ART, 0x06-0x0B)
2.4 GHz A4:39:B6:xx:xx:9F (0:ART, 0x0C-0x11)
5 GHz A4:39:B6:xx:xx:A0 (0:ART, 0x12-0x17)

Signed-off-by: Chang Liu <[email protected]>

imagebuilder: fix repeated generation of package index when signing is enabled

`$(MAKE) package_index` will generate Packages.sig if signing is enabled, and Packages.sig is always newer than Packages.gz, cause repeated generation of package index on next build. So we should ignore Packages.sig.

Signed-off-by: Liangbin Lian <[email protected]>

wifi-scripts: ucode: fix start failed

When using wpad-openssl/wpad-basic-openssl, wpa_supplicant/hostapd may not be ready because of openssl.
This cause supplicant.setup and hostapd.setup to be failed.
Therefore, wait for wpa_supplicant/hostapd to be ready before supplicant.setup and hostapd.setup.

Run-tested: mediatek/filogic GL-MT3000
fixes: #20361

Signed-off-by: Andy Chiang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>

wifi-scripts: use stationary_ap conf for AX mode

Use stationary_ap configuration for 6GHz AX AP (not only BE).
This change fixes the 6GHz network not visible issue for QCN9024.

Signed-off-by: Paweł Owoc <[email protected]>

kernel: fix mtk_eth_soc handling of fraglist packets without GSO_FRAGLIST

Fixes tx hangs when disabling rx fraglist GRO

Signed-off-by: Felix Fietkau <[email protected]>

prereq-build: add Python 3.13 support

Add support for Python version 3.13 to include/prereq-build.mk.
One of the reasons for this change is that
Ubuntu 25.04 ships with Python 3.13 as default version.
Let's support it.

Signed-off-by: Kacper Ludwinski <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20735
Signed-off-by: Christian Marangi <[email protected]>

scripts: feeds: Don’t hardcode IS_TTY

When building in environments that set IS_TTY, the feeds script does not
honor it and passes a hardcoded value to scan.mk, causing unwanted
control characters to appear in stdout.

This commit addresses the issue by checking IS_TTY and MAKE_TERMOUT
variables and uses their values if defined.

Closes #8039

Signed-off-by: Ernestas Kulik <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20743
Signed-off-by: Christian Marangi <[email protected]>

openssl: add MODULES_DIR MACRO for provider

Add MODULES_DIR MACRO for provider useful if the relevant package
require to define the default OpenSSL MODULES_PATH.

Signed-off-by: Christian Marangi <[email protected]>

firmware-utils: update to Git HEAD (2025-11-11)

313f344d8436 dlink-sge-image: add support for D-Link DIR-X1860 B1/DIR-X1550 A1
ac7a4abdde7d iptime-crc32: add support for ipTIME AX3000SE
c42a3bc53da8 iptime-crc32: add support for ipTIME AX2002MESH

Link: https://github.com/openwrt/openwrt/pull/20734
Signed-off-by: Hauke Mehrtens <[email protected]>

tools: firmware-utils: update to Git HEAD (2025-11-11)

ac7a4abdde7d iptime-crc32: add support for ipTIME AX3000SE
c42a3bc53da8 iptime-crc32: add support for ipTIME AX2002MESH

Link: https://github.com/openwrt/openwrt/pull/20734
Signed-off-by: Hauke Mehrtens <[email protected]>

ucode: update to Git HEAD (2025-11-07)

e8a7290e55c0 socket: fix `recv()` incorrectly reporting unrelated errors
ddde611fb9d4 socket: fix convertion of hw addresses to ucode strings
924ccc95be32 vm: make sure uc_vm_insn_to_name() always returns a value
754590d26f23 lexer: fix parsing \xHH and \0OOO escape sequences
623f550e579a fs: add dup2() function
6c9385a99edd fs: add mkdtemp() method for creating temporary directories
ea579046a619 fs: reset errno to zero in get_fd()

The removed patches are integrated upstream.

Fixes: https://github.com/jow-/ucode/issues/332
Fixes: https://github.com/jow-/ucode/issues/337
Link: https://github.com/openwrt/openwrt/pull/20718
Signed-off-by: Hauke Mehrtens <[email protected]>

tegra: promote kernel 6.12 as default

It has been stable so far. As result of this change drop 6.6 files.

Signed-off-by: Tomasz Maciej Nowak <[email protected]>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/[email protected]/
Signed-off-by: Hauke Mehrtens <[email protected]>

qualcommbe: support 10g-qxgmii in QCA8084 PHY driver

The "old" QCA8084 PHY driver does not implement 10g-qxgmii support.
This is blocking several devices which use the QCA8084 form being
merged. Qualcomm has provided updated drivers for the MAC (ppe), PCS,
and PHY via github. We only need to update the PHY driver.

Update the QCA8084 PHY driver using the patches provided by Qualcomm.
Re-organize the patches so that the changes go into the existing
patches. The SERDES functionality is new, so it gets new patches. This
is sufficient to enable 10g-qxgmii on ipq95xx platforms.

Signed-off-by: Alexandru Gagniuc <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20721
Signed-off-by: Robert Marko <[email protected]>

airoha: replace AN7583 pinctrl patch with upstream version

Replace Airoha AN7583 pinctrl patch with upstream version as it has been
accepted upstream. Add the related kernel version tag to identify it.

Signed-off-by: Christian Marangi <[email protected]>

kernel: sound: add support for MIDI 2.0 and UMP

New Packages / build options:
* sound-midi2: enable MIDI 2.0 / UMP in ALSA MIDI
* sound-midi2-seq: enable MIDI 2.0 / UMP in ALSA sequencer
* sound-midi2-usb: enable USB MIDI 2.0 support
* sound-dynamic-minors: allow more than 8 MIDI devices
More info about ALSA MIDI 2.0:
 https://docs.kernel.org/6.12/sound/designs/midi-2.0.html
More info about MIDI 2.0:
 https://midi.org/midi-2-0

Signed-off-by: Florian Bomers <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20727
Signed-off-by: Christian Marangi <[email protected]>

ipq40xx: fix unit-address of Netgear LBR20 ubi partition

The unit-address of the ubi partition was @a9c0000 but the partition
actually starts at offset 0x0ad00000. Ideally they should match, so
align them.

Signed-off-by: Christoph Krapp <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20733
Signed-off-by: Robert Marko <[email protected]>

realtek: dsa: Clarify meaning of secondary lag member variable

The name "is_lagmember" implies that the port is part of a LAG. But this
information is already stored in lagmembers. In reality, it is stored the
non-primary LAG members. Renaming it accordingly, makes the code a lot more
readable

Also the type (u32 array) looks like it would contain some kind of large id
(like the group ID). But it only stores a single bit. It is more appropriate
to just use a single bit per port.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20707
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: DSA: Document meaning of lag priv variables

The names of the LAG variables in struct rtl838x_switch_priv are not self
explaining. They are even suggesting that they are dealing with information
which are actually stored in a different variable. As first step, document
their meaning.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20707
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: Drop LAG checks already handled by DSA handlers

There is no need to check conditions in rtl83xx_lag_add()/rtl83xx_lag_del()
when they are already checked in
rtl83xx_port_lag_join()/rtl83xx_port_lag_leave().

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20707
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: Use DSA allocated LAG ids

It is not necessary to have a private LAG id allocation when the shared DSA
code already provides the complete infrastructure for it.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20707
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: Drop secondary LAG configuration handler

The DSA code is responsible to inform the driver about link aggregation
changes. Having a second one which behaves slightly different makes the
whole process fragile and creates hard to debug problems.

It also complicates the code because the secondary event handler can also
not rely on shared DSA state to handle things like LAG ID.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20707
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: Fix LAG id allocation

The rtl83xx_lag_can_offload() function always returned an error because
ds->num_lag_ids was never set. This basically disabled the DSA lag
configuration completely.

Drop the private n_lag variable and instead use the DSA specific one. This
ensures that all the code always has the same reference for the number of
LAGs.

Fixes: 32e5b5ee6b86 ("realtek: Add Link Aggregation (aka trunking) support")
Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20707
Signed-off-by: Hauke Mehrtens <[email protected]>

udebug: update to Git HEAD (2025-10-21)

8c967bce23ae CMakeLists.txt: rename udebug-cli to udebug on installation
75f39cd4a806 add debian package support

Link: https://github.com/openwrt/openwrt/pull/20719
Signed-off-by: Hauke Mehrtens <[email protected]>

uci: update to Git HEAD (2025-11-03)

57c1e8cd2c05 github: add CI build
2e46a7405f26 github: improve CI
c1e2eee6c5e3 github: fix CI apt dependencies

Link: https://github.com/openwrt/openwrt/pull/20717
Signed-off-by: Hauke Mehrtens <[email protected]>

ubus: update to Git HEAD (2025-11-03)

6fdf7a979162 github: improve CI
0d4bcb56f5e1 github: fix CI apt dependencies

Link: https://github.com/openwrt/openwrt/pull/20716
Signed-off-by: Hauke Mehrtens <[email protected]>

ubox: update to Git HEAD (2025-10-30)

6f78fa496bf3 ubox validate: port range check fix

Link: https://github.com/openwrt/openwrt/pull/20715
Signed-off-by: Hauke Mehrtens <[email protected]>

libnl-tiny: update to Git HEAD (2025-11-03)

fa6a52b03713 github: add CI build
c69fb5ef80b9 github: improve CI
532ac744dedc github: fix CI apt dependencies

Link: https://github.com/openwrt/openwrt/pull/20714
Signed-off-by: Hauke Mehrtens <[email protected]>

libubox: update to Git HEAD (2025-11-03)

7a3863acfb15 lua: CMakeLists: drop redundant cmake_minimum_required
61cc1e6fdc0e examples: CMakeLists: drop redundant cmake_minimum_required
7d6b9d98d0bd add debian/ directory
9caf555f00e2 github: improve CI build
e357be611cd9 github: fix CI apt dependencies

Link: https://github.com/openwrt/openwrt/pull/20713
Signed-off-by: Hauke Mehrtens <[email protected]>

rockchip: add missing KERNEL_LOADADDR for LinkEase EasePi R1

Commit 8ca4caacd039 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
forgot to include the SoC recipe, which leads KERNEL_LOADADDR undefined.

Fixes: 8ca4caacd039 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Tianling Shen <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20722
Signed-off-by: Hauke Mehrtens <[email protected]>

rockchip: fix assign IRQ SMP affinity for Radxa E52C

The ifname was renamed to `lan`/`wan` in commit 1f1db7543220
 ("rockchip: make NIC name predictable for Radxa E52C/ROCK 5 ITX/ROCK 5T"),
update accordingly.

Fixes: 1f1db7543220 ("rockchip: make NIC name predictable for Radxa E52C/ROCK 5 ITX/ROCK 5T")
Signed-off-by: Tianling Shen <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20722
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: rtl93xx: Keep mgmt recv action functions local

Th function to set the mangement frames receive actions is only used in the
SoC specific files. They can therefore be kept local without any
declaration in headers.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20704
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: dsa: rtl931x: Sync mgmt recv action code with RTL930x

The code for the RTL930x management action configuration was cleaned up
significantly for commit 75fe6b2d0b91 ("realtek: rtl930x: Add support for
trapping management frames"). Sync these changes to RTL931x to make it
easier to extend both implementations.

Signed-off-by: Sven Eckelmann <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20704
Signed-off-by: Hauke Mehrtens <[email protected]>

odhcp6c: update to Git HEAD (2025-11-09)

17ef5f40d48a readme: rewrite in markdown
0fcfe9166173 readme: document all environment options
e3949977ca94 readme: update for prpl patch-set additions
86544fa2b581 src: align SoftAtHome license headers format
8bad7df9feb9 src: reorder includes alphabetically
6d353ff96826 src: remove pragma once in headers
f5684d570200 treewide: remove whitespaces at EOL
e5cfea8f6ef8 src: add missing if/else braces
a92f199d6b8d dhcpv6: potential bug fix for checking DHCPV6_OPT_STATUS
9e414d41e16e readme: fix description string
775e6c759cfd dhcpv6: return early upon success
e5690c1f13ed treewide: Replace _unused with _o_unused

This fixes the build on powerpc.

Signed-off-by: Hauke Mehrtens <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20712
Signed-off-by: Christian Marangi <[email protected]>

airoha: backport patch fixing out of order DMA for ethernet driver

Backport upstream patch fixing out of order DMA access for ethernet
driver. This is relevant in the context of QoS when packets doesn't
follow linear handling by QDMA HW.

Signed-off-by: Christian Marangi <[email protected]>

uboot-airoha: drop HIDDEN option

Drop HIDDEN option from U-Boot default for Airoha while support for ATF
gets pushed.

Signed-off-by: Christian Marangi <[email protected]>

airona: an7583: fix typo for CONFIG_PHY_AIROHA_USB

KConfig flag have an extra whitespace for CONFIG_PHY_AIROHA_USB and
value is not ignored.

Drop the extra whitespace to correctly ignore the value on kernel
compilation.

Fixes: c5b12fc02ab1 ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <[email protected]>

firewall: config: add dest addr restrictions for DHCPv6 rules

Some ISPs may use a GUA or other non-LLA as the source addr for the DHCPv6 response, but the destination addr is always LLA (fe80::/10).
Therefore, adding a dest addr restriction improves security.
See https://forum.mikrotik.com/t/xfinity-comcast-dhcpv6-configuration-change/156031/10

Signed-off-by: Andy Chiang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20562
Signed-off-by: Robert Marko <[email protected]>

wifi-scripts: allow sae_password_file to be configured

Adds missing config_add_string for sae_password_file.

Fixes: 65a1c666f2 ("hostapd: add SAE support for wifi-station and optimize PSK file creation")
Fixes: https://github.com/openwrt/openwrt/issues/19717
Signed-off-by: Rany Hany <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19964
Signed-off-by: Robert Marko <[email protected]>

toplevel.mk: use relative path for feeds/base symlink

Currently, feeds/base is created as an absolute symlink to $(TOPDIR)/package.
If the OpenWrt source tree is copied to another location for building (while keeping the old tree), the symlink will still point to the package directory in the old tree.
Using a relative symlink ensures that feeds/base always points to the package directory within the current OpenWrt source tree, improving portability and avoiding incorrect links.

Signed-off-by: Andy Chiang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20297
Signed-off-by: Robert Marko <[email protected]>

odhcpd: update Makefile description

Make it a little bit more consistant, and a bit more idiomatic.

Signed-off-by: David Härdeman <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <[email protected]>

odhcpd: update Makefile, remove homenet

The support has been removed from odhcpd, so remove the Makefile options
related to homenet.

Signed-off-by: David Härdeman <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <[email protected]>

odhcpd: reload on change to service/network cfg

"system" is used to get the current time zone, "network" is used to get
the global DUID.

Signed-off-by: David Härdeman <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <[email protected]>

odhcpd: remove legacy option

Support for this option has been removed from odhcpd, so remove it in
the defaults as well.

Signed-off-by: David Härdeman <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <[email protected]>

wifi-scripts: ucode: iwinfo: expand AKM display

This exands the list of AKMs to display:
 - display the hash when larger than the default (loosely based on
   what hostapd uses in config).
   - renaming 'WPA PSK2' to 'WPA PSK-SHA256' as a result
 - separate FILS suites from plain 802.1x
 - add suites 3, 5, 9, 19, 20, 24, and 25

Signed-off-by: Eneas U de Queiroz <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20686
Signed-off-by: Robert Marko <[email protected]>

wifi-scripts: ucode: iwinfo: escape control chars

Escape control characters when displaying ESSID.  It is not uncommon for
a scan to encounter invalid SSIDs, containing binary data.  Escape the
control characters to avoid messing the display (ENQ is particularly
bothersome).

Signed-off-by: Eneas U de Queiroz <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20686
Signed-off-by: Robert Marko <[email protected]>

wifi-scripts: ucode: iwinfo: show ESSID in scan

This adds the ESSID: line to the iwinfo scan results.

Signed-off-by: Eneas U de Queiroz <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20686
Signed-off-by: Robert Marko <[email protected]>

realtek: RTL838x: make u-boot-env writeable ZyXEL GS1900

As per #19596 - this allows eg, modifying the bootcmd etc.

This has been useful when testing on e.g the -48, where `rtk network on` is required for the SFP ports.

Signed-off-by: Joe Holden <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19913
Signed-off-by: Hauke Mehrtens <[email protected]>

rockchip: Add support for RK3568 LinkEase EasePi R1

Specification:
- Rockchip RK3568
- 2GB/4GB LPDDR4 RAM
- 16GB on-board eMMC
- 1x M.2 key for 2280 NVMe (PCIe 3.0)
- 1x USB 3.0 Type-A
- 1x USB 2.0 Type-C (for USB flashing)
- 2x 1000 Base-T (native, RTL8211F)
- 2x 2500 Base-T (PCIe, RTL8125B)
- 1x HDMI 2.0 Output
- 12v DC Jack
- 1x Power key connected to PMIC
- 2x LEDs (one static power supplied, one GPIO controlled)

Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds,
'J7' on board with G/R/T (GND/RX/TX) pins marked

Installation - eMMC:
-Boot official firmware (OpenWRT based)
-Upload sysupgrade.img.gz to /tmp/firmware.bin (with scp or web page)
-Flash to eMMC: sysupgrade -n -p -F /tmp/firmware.bin

Signed-off-by: Liangbin Lian <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20147
Signed-off-by: Hauke Mehrtens <[email protected]>

uboot-rockchip: add support for LinkEase EasePi R1

generic-rk3568 is enough

Signed-off-by: Liangbin Lian <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20147
Signed-off-by: Hauke Mehrtens <[email protected]>

mediatek/filogic: fix Cudy WR3000H ethernet port order

The ports are physically labelled in reverse order on the device.
This patch aligns logical names with physical ones.
LED order on front of device is correct after this patch.

Fixes: 9d66b8b312fb6a4087244ee3ee10e1ba1623df81
Signed-off-by: Thibaut VARÈNE <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20528
Signed-off-by: Hauke Mehrtens <[email protected]>

uboot-d1: fix build with swig 4.3.0

Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an
additional parameter `is_void`. SWIG_AppendOutput remains unchanged.
This was fixed upstream in u-boot/u-boot@a63456b

```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
 5581 |     resultobj = SWIG_Python_AppendOutput(resultobj, val);
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~
```

This is the same fix as applied in 363e07d.

Fixes: #20619
Link: #20620
Signed-off-by: Trix Taiclet <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20620
Signed-off-by: Hauke Mehrtens <[email protected]>

kirkwood: kernel: remove 6.6 version support

After switching to 6.12, time to remove 6.6 support.

Signed-off-by: Pawel Dembicki <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20672
Signed-off-by: Hauke Mehrtens <[email protected]>

kirkwood: kernel: switch to 6.12 version

No new reggresions was observed. Time to switch to 6.12.

Signed-off-by: Pawel Dembicki <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20672
Signed-off-by: Hauke Mehrtens <[email protected]>

tools/squashfs4: update to 4.7.3

Release Note:
  https://github.com/plougher/squashfs-tools/releases/tag/4.7.3

The three backported patches fixed the regression and build
issue on squashfs-tools v4.7.3.

Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20683
Signed-off-by: Hauke Mehrtens <[email protected]>

rockchip: make NIC name predictable for Radxa E52C/ROCK 5 ITX/ROCK 5T

The probe order for PCIe buses and devices is non-deterministic,
making the names eth0 and eth1 unpredictable (they may be swapped).

This patch fixes the names by referencing the device path using
`ucidef_set_network_device_path`.

The mapping between silkscreen labels on the board/case and OpenWrt
interface names is as follows:

- E52C
  LAN: lan
  WAN: wan

- ROCK 5 ITX
  RJ45 1: eth0
  RJ45 2: eth1

- ROCK 5T
  RJ45_1: eth0
  RJ45_2: eth1

For Radxa E52C, this breaks compatibility of the network config;
therefore, set DEVICE_COMPAT_VERSION to `1.1`.

Fixes: d16d2765bd ("rockchip: add support for Radxa E52C")
Fixes: 0839345211 ("rockchip: add support for Radxa ROCK 5 ITX/ITX+")
Fixes: 4a78af9876 ("rockchip: add support for Radxa ROCK 5T")
Link: https://github.com/openwrt/openwrt/issues/20202
Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20608
Signed-off-by: Hauke Mehrtens <[email protected]>

mediatek: add support for COMFAST CF-WR632AX

COMFAST CF-WR632AX is a compact/travel (123.4 mm * 88.7 mm * 34 mm)
wireless WiFi 6 router.

Specification
-------------
- SoC          : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz
- RAM          : DDR3 512 MiB
- Flash        : SPI-NAND 128 MiB (Winbond)
- WLAN         : MediaTek MT7976CN dual-band WiFi 6
  - 2.4 GHz    : b/g/n/ax, MU-MIMO (2x 5 dBi antennas)
  - 5 GHz      : a/n/ac/ax, MU-MIMO (2x 5 dBi antennas)
- Ethernet     :
  - LAN x1     : 10/100/1000 Mbps (MT7981 internal PHY)
  - WAN x1     : 10/100/1000/2500 Mbps (Maxlinear GPY211C)
- USB x1       : 3.0
- UART         : through-hole on PCB
  - assignment : (RX), (TX), (GND), [VCC]
  - settings   : 115200n8
- Buttons x1   : Reset
- LEDs x3      : Status (Blue, Green, Red)
- Fan x1       : PWM, 4-wire, 5 V, 0.3 A, 45 mm * 10 mm
- Power        : 5 VDC, 3 A, Type-C

Flash instructions
------------------
WebUI Method:

1. Install the *squashfs-sysupgrade.bin image using the stock WebUI
   update page.
2. Press and hold the reset button after reboot
   to wipe the stock config.

SSH Method:

1. Import stock firmware settings from backup file
   github.com/andros-ua/owrt-misc/blob/main/cf-wr632ax/backup.file
   Note: WebUI password will be reset to admin1234 after import.
2. Connect via SSH using root:openwrt credentials.
3. Upload the *squashfs-sysupgrade.bin image.
4. Use the command: sysupgrade -n
   All checks should pass.

Return to stock
---------------
Flash a stock firmware
using the OpenWrt sysupgrade method.

Recovery
--------
Power on the router while holding the Reset button until
the LED flashes 5 times.
The U-Boot Flash WebUI will be available at http://192.168.1.1
or
Connect UART and use the U-Boot menu to flash the firmware image
or boot an OpenWrt initramfs image.

OpenWrt U-Boot flash instructions
---------------------------------
1. Flash ordinary OpenWrt image.
2. Login into the device and backup everything, especially 'Factory' part.
3. Unlock mtd partitions:
    apk add kmod-mtd-rw
    insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
    mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-preloader.bin BL2
    mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
    ip 192.168.1.254 mask 255.255.255.0
6. Serve OpenWrt initramfs image using TFTP server.
7. Reboot device, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.

MAC Addresses:
----------------------------------------------------------
| Interface    |  MAC              | Source              |
---------------|-------------------|----------------------
| WAN (label)  | 40:A5:EF:xx:xx:xx | Factory, 0xe000     |
| LAN          | 40:A5:EF:xx:xx:xx | Factory, 0xe000 + 1 |
| WLAN 2.4 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x4        |
| WLAN 5 GHz   | 40:A5:EF:xx:xx:xx | Factory, 0x8000     |
----------------------------------------------------------

Signed-off-by: Andrii Kuiukoff <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20382
Signed-off-by: Hauke Mehrtens <[email protected]>

ramips: mt7621: add support for Cudy AP1300 Outdoor v1

Hardware:
 - SoC: MediaTek MT7621DAT
 - Flash: 16 MiB XM25QH128C
 - RAM: 128 MiB
 - WLAN: 2.4 GHz (MT7603E, 11n), 5 GHz (MediaTek MT7613BEN, 11ac)
 - Ethernet: 1x10/100/1000 Mbps LAN
 - Buttons: 1 Reset button, 1 WPS button
 - LEDs: 5x Green
 - Serial Console: unpopulated header 115200 8n1 (silkscreen on PCB)
 - Power: POE 802.3af (37-57V DC)

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| LAN     | 80:af:ca:xx:xx:x0 | label     |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label     |
| WLAN 5g | 82:af:ca:xx:xx:x1 | +1        |
+---------+-------------------+-----------+

Installation:
The factory firmware is locked: you can only work with Cudy signed firmware.
Download a intermediate firmware signed by Cudy here:
https://www.cudy.com/blogs/faq/openwrt-software-download

After that, login to the router (192.168.10.254, password "admin") and install the intermediate firmware.

If you can reach LuCI or SSH now on the intermediate firmware, just use the sysupgrade image with the 'Keep settings' option turned off.

Special thanks to Daniel de Kock for starting the porting work at #16265.

Signed-off-by: Luis Mita <[email protected]>
Co-Authored-By: Daniel de Kock <[email protected]>
Co-Authored-By: Hauke Mehrtens <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20268
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: pcs: allow to configure SerDes polarity

Allow to configure SerDes polarity in device tree. To achieve this, add
new device tree properties that can be set in the device tree definition
of the SerDes, are read by the PCS driver during probe and are applied
upon SerDes setup.

This may be required for supporting new devices as the SerDes polarity
is usually subject to the vendors board design and defined in the
hardware profile (HWP) in the SDK. Most importantly, it is quite an
important step towards being able to setup everything on our own instead
of relying on the bootloader.

Signed-off-by: Jonas Jelonek <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20648
Signed-off-by: Hauke Mehrtens <[email protected]>

realtek: pcs: rtl93xx: provide proper SerDes polarity configuration

The configuration code for RTL930X already provides setting the SerDes
TX and RX PN polarity. This is covered by a function called
'..._sds_mac_link_config'. But despite its name, this function only sets
the SerDes polarity and nothing more.

Moreover, this was called always with 'not inverted' in the SerDes setup
code and thus not really allowing to be configured.

At first, streamline the SerDes polarity configuration code. Rename the
function to reflect what it actually does instead of giving the
impression of doing more. Improve the implementation of this for better
readability.

As the implementation, page, register, bits, etc. are exactly the same
for both RTL930X and RTL931X (compare [1] and [2]), move and name it
accordingly so we can also add support for RTL931X.

[1] https://github.com/plappermaul/realtek-doc/blob/69d2890a2e2d7a03df6e40e2cd2c32ff5b074dcf/sources/rtk-xgs1210/src/hal/phy/phy_rtl9300.c#L1384
[2] https://github.com/plappermaul/realtek-doc/blob/69d2890a2e2d7a03df6e40e2cd2c32ff5b074dcf/sources/rtk-xgs1210/src/hal/phy/phy_rtl9310.c#L3479

Signed-off-by: Jonas Jelonek <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20648
Signed-off-by: Hauke Mehrtens <[email protected]>

kernel: mtdsplit_fit: always return 0 when partition can't be split

If parse_fn() callback returns any error code, the entire MTD partition
table will be destroyed. Returning "0" indicates that the partition
should not be split. This patch fixes the kernel warning when running
the initramfs image but there is no image in firmware partition:

```
[    1.554246] no rootfs found after FIT image in "firmware"
[    1.559686] Failed to parse subpartitions: -19
[    1.564120] Deleting MTD partitions on "spi0.0":
[    1.568743] Deleting bl2 MTD partition
[    1.572507] ------------[ cut here ]------------
[    1.577110] WARNING: CPU: 0 PID: 1 at del_gendisk+0x260/0x2c4
[    1.582855] Modules linked in:
[    1.585902] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.57 #0
[    1.592505] Hardware name: AiroPi AX3 (DT)
[    1.596589] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    1.603538] pc : del_gendisk+0x260/0x2c4
[    1.607452] lr : del_gendisk+0x1c/0x2c4
[    1.611280] sp : ffffffc080dab460
[    1.614583] x29: ffffffc080dab460 x28: ffffffc080d75140 x27: 0000000000000004
[    1.621711] x26: 0000000000000000 x25: 0000000000000000 x24: ffffffc080b3f3d0
[    1.628838] x23: ffffffc080cf3d78 x22: ffffffc080cf3da8 x21: ffffff80009b8780
[    1.635966] x20: ffffffc080cf3e10 x19: ffffff80009d7400 x18: ffffffc080c5ebd8
[    1.643093] x17: ffffffc080cf00f0 x16: 000000009d594d00 x15: 0000000000000088
[    1.650221] x14: 0000000000000088 x13: 00000000ffffffea x12: ffffffc080cb6b80
[    1.657348] x11: 0000000000000040 x10: ffffffc080cf3820 x9 : ffffffc080cf3818
[    1.664475] x8 : ffffff8000420dd8 x7 : 0000000000000000 x6 : 0000000000000000
[    1.671601] x5 : ffffff8000420db0 x4 : ffffff8000420dd8 x3 : 0000000000000000
[    1.678728] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000004
[    1.685855] Call trace:
[    1.688290]  del_gendisk+0x260/0x2c4
[    1.691858]  del_mtd_blktrans_dev+0x30/0x144
[    1.696120]  mtdblock_remove_dev+0xc/0x20
[    1.700119]  blktrans_notify_remove+0x88/0xc4
[    1.704464]  del_mtd_device+0x58/0xdc
[    1.708120]  __del_mtd_partitions+0x98/0xe0
[    1.712296]  del_mtd_partitions+0x50/0x70
[    1.716299]  add_mtd_partitions+0x94/0x1e0
[    1.720388]  parse_mtd_partitions+0x3d0/0x4d4
[    1.724736]  mtd_device_parse_register+0x170/0x36c
[    1.729518]  spi_nor_probe+0x250/0x2cc
[    1.733261]  spi_mem_probe+0x68/0xa0
[    1.736828]  spi_probe+0x80/0xe0
[    1.740051]  really_probe+0xb8/0x2a4
[    1.743617]  __driver_probe_device+0x74/0x118
[    1.747962]  driver_probe_device+0x3c/0xe0
[    1.752049]  __device_attach_driver+0xac/0xe8
[    1.756394]  bus_for_each_drv+0x6c/0xb0
[    1.760224]  __device_attach+0x98/0x178
[    1.764049]  device_initial_probe+0x10/0x18
[    1.768223]  bus_probe_device+0xa0/0xa4
[    1.772051]  device_add+0x540/0x724
[    1.775531]  __spi_add_device+0x13c/0x1f8
[    1.779532]  of_register_spi_device+0x44c/0x720
[    1.784051]  spi_register_controller+0x4cc/0x6c0
[    1.788658]  devm_spi_register_controller+0x48/0xa0
[    1.793525]  mtk_spi_probe+0x420/0x720
[    1.797266]  platform_probe+0x64/0xcc
[    1.800920]  really_probe+0xb8/0x2a4
[    1.804485]  __driver_probe_device+0x74/0x118
[    1.808831]  driver_probe_device+0x3c/0xe0
[    1.812916]  __driver_attach+0x88/0x154
[    1.816741]  bus_for_each_dev+0x60/0xa0
[    1.820569]  driver_attach+0x20/0x28
[    1.824138]  bus_add_driver+0xdc/0x208
[    1.827880]  driver_register+0x64/0x114
[    1.831705]  __platform_driver_register+0x20/0x30
[    1.836399]  mtk_spi_driver_init+0x18/0x20
[    1.840486]  do_one_initcall+0x4c/0x1f8
[    1.844313]  kernel_init_freeable+0x238/0x290
[    1.848661]  kernel_init+0x1c/0x120
[    1.852141]  ret_from_fork+0x10/0x20
[    1.855707] ---[ end trace 0000000000000000 ]---
[    1.860731] Deleting u-boot-env MTD partition
[    1.865431] Deleting factory MTD partition
[    1.869907] Deleting fip MTD partition
[    1.874003] Deleting firmware MTD partition
```

Ref:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/mtd/mtdpart.c?h=linux-6.12.y&id=5c2f7727d437cd42033d13ebc8b3d74b9fe65712

Signed-off-by: Shiji Yang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20706
Signed-off-by: Hauke Mehrtens <[email protected]>

ppp: add reqprefix norelease ac_mac

Use ppp and enable autoipv6, odhcp6c supports reqprefix and norelease to minimize the chance of IPv6 PD changes.[1]
PPPoE supports connecting to a specific AC/BRAS by using the pppoe-mac parameter.[2]

1. https://github.com/openwrt/openwrt/blob/master/package/network/ipv6/odhcp6c/files/dhcpv6.sh#L67
   https://github.com/openwrt/openwrt/blob/master/package/network/ipv6/odhcp6c/files/dhcpv6.sh#L77
2. https://github.com/ppp-project/ppp/blob/master/pppd/plugins/pppoe/plugin.c#L93

Signed-off-by: Andy Chiang <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/19978
Signed-off-by: Robert Marko <[email protected]>

bcm53xx: use -ENOENT error for TRX parser workaround patch

Change return value from -EINVAL to -ENOENT for the TRX parser
workaround patch as it's better suited and it's the common exit error
for parser failing parsing for expected condition (partition not init,
zero partition found in the schema, magic values not matching)

Also this is needed for a pending upstream patch that will permit parser
to fail and be skipped for subpartitions only with the -ENOENT error.

Signed-off-by: Christian Marangi <[email protected]>

mediatek: filogic: add support for TP-LINK BE450

This commit adds support for TP-LINK BE450.

Device specification
--------------------
SoC Type:   MediaTek MT7988D, Cortex-A73, 64-bit
RAM:        512MB
Flash:      SPI NAND GigaDevice (128 MiB)
Ethernet:   MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N)

WLAN:       MT7992
WLAN 2g:    MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g:    MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4
LEDs:       8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet
        blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled
Button:     2 (Reset, WPS)
USB port:   Yes
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0
            partition contain "seconduboot" (also U-Boot 2023.10-rc4)

Serial console (UART), unpopulated, located near the power connector
---------------------
heatsink
|   |
|   |
|   |     +----+-----+------+-------+               +-----------------+
|   |     | TX |  RX |  GND | +3.3V |               | power connector |
+---+     +----+-----+------+-------+               +-----------------+
                                  |
                Don't connect ----+

Disassemble: rm the 2 screws at the bottom and the one at the backside.
             un-clip the case starting at the edge above the LEDs.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit:
      https://github.com/openwrt/openwrt/commit/b77fa45d1278443d534919598c0301719fed2784

      The second ubi partition (ubi1) is empty and there is no known
      dual-partition mechanism, neither in u-boot nor in the stock firmware.

      NMBM is not used.

Not Working: WED, if activated, MT7992 isn't recognized any more.

Signed-off-by: Dirk Buchwalder <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20398
Signed-off-by: Hauke Mehrtens <[email protected]>

pcre2: bump to 10.47

Update to latest version.

Changelog: https://github.com/PCRE2Project/pcre2/blob/pcre2-10.47/ChangeLog

Tested with snort3, no regressions.

Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc (Intel N150 based box)

Signed-off-by: John Audia <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20554
Signed-off-by: Hauke Mehrtens <[email protected]>

kernel: generic: mtdsplit_seil: return 0 instead of -ENODEV

Return 0 if the current mtd is inactive or no valid header/rootfs found,
instead of -ENODEV.
Linux Kernel 6.7 and later versions handle all errors returned by mtd
parsers, including -ENODEV as error. So '0' needs to be returned if no
child partitions were not parsed.

Signed-off-by: INAGAKI Hiroshi <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20697
Signed-off-by: Hauke Mehrtens <[email protected]>

util-linux: Update to version 2.41.2

Changes:
https://www.kernel.org/pub/linux/utils/util-linux/v2.41/v2.41.2-ReleaseNotes

Link: https://github.com/openwrt/openwrt/pull/20546
Signed-off-by: Hauke Mehrtens <[email protected]>

tools: util-linux: Update to version 2.41.2

Changes:
https://www.kernel.org/pub/linux/utils/util-linux/v2.41/v2.41.2-ReleaseNotes

Link: https://github.com/openwrt/openwrt/pull/20546
Signed-off-by: Hauke Mehrtens <[email protected]>