From: Dirk Buchwalder Date: Fri, 10 Oct 2025 19:51:07 +0000 (+0200) Subject: mediatek: filogic: add support for TP-LINK BE450 X-Git-Url: http://git.openwrt.org/?a=commitdiff_plain;h=71ebc54d2a73b0bd0a7d712d472df9c01ace74f2;p=openwrt%2Fstaging%2Fstintel.git mediatek: filogic: add support for TP-LINK BE450 This commit adds support for TP-LINK BE450. Device specification -------------------- SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit RAM: 512MB Flash: SPI NAND GigaDevice (128 MiB) Ethernet: MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N) WLAN: MT7992 WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4 WLAN 5g: MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4 LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled Button: 2 (Reset, WPS) USB port: Yes Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0 partition contain "seconduboot" (also U-Boot 2023.10-rc4) Serial console (UART), unpopulated, located near the power connector --------------------- heatsink | | | | | | +----+-----+------+-------+ +-----------------+ | | | TX | RX | GND | +3.3V | | power connector | +---+ +----+-----+------+-------+ +-----------------+ | Don't connect ----+ Disassemble: rm the 2 screws at the bottom and the one at the backside. un-clip the case starting at the edge above the LEDs. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000 4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit: https://github.com/openwrt/openwrt/commit/b77fa45d1278443d534919598c0301719fed2784 The second ubi partition (ubi1) is empty and there is no known dual-partition mechanism, neither in u-boot nor in the stock firmware. NMBM is not used. Not Working: WED, if activated, MT7992 isn't recognized any more. Signed-off-by: Dirk Buchwalder Link: https://github.com/openwrt/openwrt/pull/20398 Signed-off-by: Hauke Mehrtens --- diff --git a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic index 3f7ab7ade2..909848744b 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic @@ -127,7 +127,8 @@ smartrg,sdg-8733a|\ smartrg,sdg-8734) ubootenv_add_mmc "u-boot-env" "mmcblk0" "0x0" "0x8000" "0x8000" ;; -tplink,archer-ax80-v1) +tplink,archer-ax80-v1|\ +tplink,be450) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" "8" ;; ubnt,unifi-6-plus) diff --git a/target/linux/mediatek/dts/mt7988d-tplink-be450.dts b/target/linux/mediatek/dts/mt7988d-tplink-be450.dts new file mode 100644 index 0000000000..62218bf747 --- /dev/null +++ b/target/linux/mediatek/dts/mt7988d-tplink-be450.dts @@ -0,0 +1,409 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "mt7988a.dtsi" +#include +#include +#include +#include +#include + +/ { + model = "TP-Link BE450"; + compatible = "tplink,be450", "mediatek,mt7988d"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + serial0 = &serial0; + label-mac-device = &gmac0; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + memory@40000000 { + reg = <0x0 0x40000000 0x0 0x40000000>; + device_type = "memory"; + }; + + cpus { + /delete-node/ cpu@3; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&pio 14 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led-0 { + gpios = <&pio 21 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WAN; + }; + + led-1 { + gpios = <&pio 28 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + }; + + led-2 { + gpios = <&pio 29 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + }; + + led_status: led-3 { + gpios = <&pio 30 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_STATUS; + panic-indicator; + }; + + led-4 { + gpios = <&pio 31 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_LAN; + }; + + led-5 { + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_WPS; + }; + + led-6 { + gpios = <&pio 57 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WAN; + }; + + led-7 { + gpios = <&pio 68 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_USB; + }; + }; +}; + +&cpu0 { + proc-supply = <&rt5190_buck3>; +}; + +&cpu1 { + proc-supply = <&rt5190_buck3>; +}; + +&cpu2 { + proc-supply = <&rt5190_buck3>; +}; + +&cci { + proc-supply = <&rt5190_buck3>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + + reg = <0>; + + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + spi-cal-addrlen = <5>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-datalen = <7>; + spi-cal-enable; + spi-cal-mode = "read-data"; + + spi-max-frequency = <52000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0x0 0x200000>; + read-only; + }; + + partition@200000 { + label = "u-boot-env"; + reg = <0x200000 0x100000>; + }; + + partition@300000 { + label = "ubi0"; + reg = <0x300000 0x3200000>; + }; + + partition@3500000 { + label = "ubi1"; + reg = <0x3500000 0x3200000>; + read-only; + }; + + partition@6700000 { + label = "userconfig"; + reg = <0x6700000 0x800000>; + read-only; + }; + + partition@6f00000 { + label = "tp_data"; + reg = <0x6f00000 0x800000>; + read-only; + }; + }; + }; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio0_pins>; + status = "okay"; +}; + +&gmac0 { + status = "okay"; +}; + +&gmac1 { + phy-mode = "internal"; + phy-connection-type = "internal"; + phy = <&int_2p5g_phy>; + status = "okay"; +}; + +&gmac2 { + phy-mode = "usxgmii"; + phy-connection-type = "usxgmii"; + phy = <&phy0>; + status = "okay"; +}; + +&gsw_phy3 { + status = "disabled"; +}; + +&mdio_bus { + phy0: ethernet-phy@0 { + /* RTL8261N */ + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + + reset-gpios = <&pio 3 GPIO_ACTIVE_LOW>; + reset-assert-us = <100000>; + reset-deassert-us = <100000>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + + rt5190a_64: rt5190a@64 { + compatible = "richtek,rt5190a"; + reg = <0x64>; + /*interrupts-extended = <&gpio26 0 IRQ_TYPE_LEVEL_LOW>;*/ + vin2-supply = <&rt5190_buck1>; + vin3-supply = <&rt5190_buck1>; + vin4-supply = <&rt5190_buck1>; + + regulators { + rt5190_buck1: buck1 { + regulator-name = "rt5190a-buck1"; + regulator-min-microvolt = <5090000>; + regulator-max-microvolt = <5090000>; + regulator-allowed-modes = + ; + regulator-boot-on; + regulator-always-on; + }; + + buck2 { + regulator-name = "vcore"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + rt5190_buck3: buck3 { + regulator-name = "vproc"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + }; + + buck4 { + regulator-name = "rt5190a-buck4"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-allowed-modes = + ; + regulator-boot-on; + regulator-always-on; + }; + + ldo { + regulator-name = "rt5190a-ldo"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_1_pins>; + reset-gpios = <&pio 7 GPIO_ACTIVE_LOW>; + status = "okay"; + + pcie@0,0 { + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + + mt7996@0,0 { + reg = <0x0000 0 0 0 0>; + }; + }; +}; + +&pio { + button_pins: button-pins { + pins = "GPIO_RESET", "GPIO_WPS"; + bias-disable; /* bias-disable */ + }; + + mdio0_pins: mdio0-pins { + mux { + function = "eth"; + groups = "mdc_mdio0"; + }; + + conf { + groups = "mdc_mdio0"; + drive-strength = ; + }; + }; + + i2c0_pins: i2c0-pins-g0 { + mux { + function = "i2c"; + groups = "i2c0_1"; + }; + }; + + pcie0_1_pins: pcie0-pins-g1 { + mux { + function = "pcie"; + groups = "pcie_2l_0_pereset", "pcie_clk_req_n0_0"; + }; + }; + + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; + + enable-usb-power { + gpio-hog; + gpios = <32 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "USB power"; + }; +}; + +&ssusb1 { + status = "okay"; +}; + +&switch { + status = "okay"; + + ports { + port@0 { + label = "lan3"; + }; + + port@1 { + label = "lan2"; + }; + + port@2 { + label = "lan1"; + }; + + port@3 { + status = "disabled"; + }; + }; +}; + +&tphy { + status = "okay"; +}; + +&serial0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index 6b5c92086c..549489766c 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -214,6 +214,11 @@ teltonika,rutc50) totolink,x6000r) ucidef_set_led_netdev "wan" "wan" "green:wan" "wan" "link tx rx" ;; +tplink,be450) + ucidef_set_led_netdev "br-lan" "lan" "blue:lan" "br-lan" "link tx rx" + ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan-2ghz" "phy0.0-ap0" + ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan-5ghz" "phy0.1-ap0" + ;; tplink,fr365-v1) ucidef_set_led_netdev "port2-green-act" "port-2" "green:port2_act" "port2" "link tx rx" ucidef_set_led_netdev "port1-green-act" "port-1" "green:sfp" "port1" "link tx rx" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index ba1465d83d..2ce5eb0f8e 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -159,6 +159,9 @@ mediatek_setup_interfaces() tplink,archer-ax80-v1) ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" eth1 ;; + tplink,be450) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 eth2" eth1 + ;; tplink,re6000xd) ucidef_set_interface_lan "lan1 lan2 eth1" ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata index c92b2926fe..d51661a60d 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata @@ -35,6 +35,14 @@ case "$FIRMWARE" in ;; esac ;; +"mediatek/mt7996/mt7992_eeprom.bin") + case "$board" in + tplink,be450) + ln -sf /tmp/tp_data/MT7992_EEPROM.bin \ + /lib/firmware/$FIRMWARE + ;; + esac + ;; *) exit 1 ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 0516889959..86e0a02932 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -156,6 +156,7 @@ case "$board" in ;; mercusys,mr90x-v1|\ tplink,archer-ax80-v1|\ + tplink,be450|\ tplink,re6000xd) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part index 1ef2c7c267..49aeb39eec 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part @@ -16,6 +16,7 @@ preinit_mount_cfg_part() { mercusys,mr80x-v3|\ mercusys,mr90x-v1|\ tplink,archer-ax80-v1|\ + tplink,be450|\ tplink,re6000xd) mount_ubi_part "tp_data" "tp_data" ;; diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh index f9401b0389..57414837cb 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -43,6 +43,11 @@ preinit_set_mac_address() { addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) ip link set dev eth1 address "$(macaddr_add $addr 1)" ;; + tplink,be450) + addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) + ip link set dev eth1 address "$(macaddr_add $addr 1)" + ip link set dev eth2 address "$(macaddr_add $addr 2)" + ;; tplink,fr365-v1) lan_mac=$(strings /dev/mtd11 | grep 'option macaddr' | awk -F"'" '{print $2}') wan_mac="$(macaddr_add $lan_mac 1)" diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 71e99dc78f..e6e5d27233 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -182,6 +182,7 @@ platform_do_upgrade() { mercusys,mr80x-v3|\ mercusys,mr90x-v1|\ tplink,archer-ax80-v1|\ + tplink,be450|\ tplink,re6000xd) CI_UBIPART="ubi0" nand_do_upgrade "$1" diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 94a12cfa57..31b3ecaad6 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -2234,6 +2234,21 @@ define Device/tplink_archer-ax80-v1 endef TARGET_DEVICES += tplink_archer-ax80-v1 +define Device/tplink_be450 + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := BE450 + DEVICE_DTS := mt7988d-tplink-be450 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7992-firmware kmod-usb3 \ + mt7988-2p5g-phy-firmware mt7988-wo-firmware + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 51200k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += tplink_be450 + define Device/tplink_re6000xd DEVICE_VENDOR := TP-Link DEVICE_MODEL := RE6000XD