mediatek: filogic: add support for Widelantech WAP430X

This AX3000 flying saucer-shaped device is sold under a few names:
- Widelantech WAP430X
  http://www.widelantech.com/?m=home&c=View&a=index&aid=131
- Felicomm
- UeeVii UAP200 (sold on amazon.com)
True name, as marked on the PCB and as appears in the DTS, is WAP430X.

Hardware:
- SoC: Mediatek MT7981B
- RAM: 256MiB DDR3
- ROM: 16MiB NOR flash (Winbond 25Q128JVSQ)
- Wired: one GbE RJ45 port
- Wireless: Mediatek MT7976CN DBDC
- Antennas: Internal (two 2.4 GHz 4.5 dBi, three 5 GHz 6 dBi)
- GPIO: two blue LEDs (status, WLAN), one button (reset)
- Power: DC5521 (12V) or 802.3af PoE (48V 0.3A)
- UART: J500 on PCB [3v3] (Rx) (Tx) (Gnd), 115200n

Original firmware is GECOOS 8.0_2024081000, a fork of OpenWrt 21.02
created by Widelantech. All ports are closed except 443 (web management
interface) and 80 (redirects to 443). UART is locked down, but U-Boot
bootloader is friendly.

Installation is done via UART (see note below).

Method 1: press any key during boot to enter MTK U-Boot bootloader,
then choose option 2 (Upgrade firmware) and upload sysupgrade binary
via TFTP (or via Xmodem).

Method 2: put sysupgrade binary on a webserver (http, not https); after
GECOOS loads, choose option 4 (固件在线升级 = online firmware upgrade)
in the menu and enter the URL to the sysupgrade binary.

Note: GECOOS has a slick web management, and firmware can be uploaded
at https://6.6.6.6/#/system/sysupgrade but it's still not clear how to
convert the sysupgrade binary to a factory binary accepted by the web
interface (WIP).

Signed-off-by: Rani Hod <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20402
Signed-off-by: Hauke Mehrtens <[email protected]>

diff --git a/target/linux/mediatek/dts/mt7981b-widelantech-wap430x.dts b/target/linux/mediatek/dts/mt7981b-widelantech-wap430x.dts
new file mode 100644 (file)
index 0000000..9faaf24
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-widelantech-wap430x.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "mt7981b.dtsi"
+
+/ {
+       compatible = "widelantech,wap430x", "mediatek,mt7981b";
+       model = "Widelantech WAP430X";
+
+       aliases {
+               label-mac-device = &gmac1;
+               led-boot = &led_system;
+               led-failsafe = &led_system;
+               led-running = &led_system;
+               led-upgrade = &led_system;
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               btn-0 {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_system: led-0 {
+                       function = LED_FUNCTION_STATUS;
+                       color = <LED_COLOR_ID_BLUE>;
+                       gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               led-1 {
+                       function = LED_FUNCTION_WLAN;
+                       color = <LED_COLOR_ID_BLUE>;
+                       gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy1tpt";
+               };
+       };
+
+       memory@40000000 {
+               device_type = "memory";
+               reg = <0 0x40000000 0 0x10000000>;
+       };
+};
+
+&eth {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mdio_pins>;
+
+       status = "okay";
+
+       gmac1: mac@1 {
+               compatible = "mediatek,eth-mac";
+               reg = <1>;
+               phy-mode = "gmii";
+               phy-handle = <&int_gbe_phy>;
+
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_factory_24>;
+       };
+};
+
+&pio {
+       spi2_flash_pins: spi2-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi2", "spi2_wp_hold";
+               };
+       };
+};
+
+&spi2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi2_flash_pins>;
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+
+               spi-max-frequency = <52000000>;
+               spi-tx-bus-width = <4>;
+               spi-rx-bus-width = <4>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "BL2";
+                               reg = <0x00000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x40000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@50000 {
+                               label = "Factory";
+                               reg = <0x50000 0xb0000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       eeprom_factory: eeprom@0 {
+                                               reg = <0x0 0x1000>;
+                                       };
+
+                                       // LAN MAC address
+                                       macaddr_factory_24: macaddr@24 {
+                                               reg = <0x24 0x6>;
+                                       };
+
+                                       // WAN MAC address (not used)
+                                       /* macaddr@2a {
+                                               reg = <0x2a 0x6>;
+                                       }; */
+                               };
+                       };
+
+                       partition@100000 {
+                               label = "FIP";
+                               reg = <0x100000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@180000 {
+                               compatible = "denx,fit";
+                               label = "firmware";
+                               reg = <0x180000 0xe70000>;
+                       };
+
+                       partition@ff0000 {
+                               label = "opt";
+                               reg = <0xff0000 0x10000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&wifi {
+       status = "okay";
+       nvmem-cells = <&eeprom_factory 0>;
+       nvmem-cell-names = "eeprom";
+};

diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index dd0a20e39c3cd5fe938405d7a6cb4a27c0848b8a..8a30fc0b1f668c4a53d878e4749bb15f1b17ddb7 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -112,6 +112,7 @@ mediatek_setup_interfaces()
        openfi,6c|\
        ubnt,unifi-6-plus|\
        wavlink,wl-wn573hx3|\
+       widelantech,wap430x|\
        zyxel,nwa50ax-pro)
                ucidef_set_interface_lan "eth0"
                ;;

diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 1b3f930bc8f673ea1681e835f680ad227474d3ea..e4c60ce0d4f6087dbb9b5b95c032e5e8f202e447 100755 (executable)
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -157,9 +157,10 @@ platform_do_upgrade() {
                ;;
        cudy,re3000-v1|\
        cudy,wr3000-v1|\
-       yuncore,ax835|\
+       totolink,x6000r|\
        wavlink,wl-wn573hx3|\
-       totolink,x6000r)
+       widelantech,wap430x|\
+       yuncore,ax835)
                default_do_upgrade "$1"
                ;;
        dlink,aquila-pro-ai-m30-a1|\

diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 9f3c3c429458c879dd35003340129a058a304050..5987872e011f9e0ccb77c3c4688cf4a878a4de30 100644 (file)
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -2626,6 +2626,21 @@ define Device/wavlink_wl-wn573hx3
 endef
 TARGET_DEVICES += wavlink_wl-wn573hx3
 
+define Device/widelantech_wap430x
+  DEVICE_VENDOR := Widelantech
+  DEVICE_MODEL := WAP430X
+  DEVICE_ALT1_VENDOR := Widelantech
+  DEVICE_ALT1_MODEL := AX3000AM
+  DEVICE_ALT1_VENDOR := UeeVii
+  DEVICE_ALT1_MODEL := UAP200
+  DEVICE_DTS := mt7981b-widelantech-wap430x
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+  IMAGE_SIZE := 14784k
+  SUPPORTED_DEVICES += UAP200 AX3000AM # allow upgrade via GECOOS UART menu
+endef
+TARGET_DEVICES += widelantech_wap430x
+
 define Device/xiaomi_mi-router-ax3000t
   DEVICE_VENDOR := Xiaomi
   DEVICE_MODEL := Mi Router AX3000T