Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM Zentel A3R12E40CBF-8E
- 16 MB flash Winbond W25Q128FVSG
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>
Installation on HW rev.5:
Factory firmware can be installed via the WEB interface.
Alternatively, it is also possible to use a TFTP server
for recovery purposes:
- Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
- Set static IP of your PC to *192.168.0.66*
- Router will obtain IP 192.168.0.86 for a few seconds while
loading, when reset button pressed at power On.
And finally, there's always u-boot access through the UART.
For information visit the wiki.
Signed-off-by: Adrian Schmutzler <[email protected]>
Signed-off-by: Christian Lamparter <[email protected]>
[reworked commit message]
ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x20"
;;
tplink,archer-c2-v3|\
-tplink,tl-wr1043nd-v4)
+tplink,tl-wr1043nd-v4|\
+tplink,tl-wr1043n-v5)
ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x20"
ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
ucidef_set_led_switch "lan2" "LAN2" "tp-link:green:lan2" "switch0" "0x08"
dlink,dir-859-a1|\
engenius,epg5000|\
tplink,archer-c2-v3|\
- tplink,tl-wr1043nd-v4)
+ tplink,tl-wr1043nd-v4|\
+ tplink,tl-wr1043n-v5)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
;;
base_mac=$(mtd_get_mac_binary config 8)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
- tplink,tl-wr1043nd-v4)
+ tplink,tl-wr1043nd-v4|\
+ tplink,tl-wr1043n-v5)
base_mac=$(mtd_get_mac_binary product-info 8)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9563_tplink_tl-wr1043n.dtsi"
+
+/ {
+ compatible = "tplink,tl-wr1043n-v5", "qca,qca9563";
+ model = "TP-Link TL-WR1043N v5";
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "factory-uboot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "u-boot";
+ reg = <0x020000 0x020000>;
+ read-only;
+ };
+
+ partition@40000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x040000 0xec0000>;
+ };
+
+ info: partition@f00000 {
+ label = "product-info";
+ reg = <0xf00000 0x020000>;
+ read-only;
+ };
+
+ partition@f20000 {
+ label = "config";
+ reg = <0xf20000 0x0a0000>;
+ read-only;
+ };
+
+ partition@fc0000 {
+ label = "partition-table";
+ reg = <0xfc0000 0x010000>;
+ read-only;
+ };
+
+ partition@fd0000 {
+ label = "logs";
+ reg = <0xfd0000 0x020000>;
+ read-only;
+ };
+
+ art: partition@ff0000 {
+ label = "ART";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
endef
TARGET_DEVICES += tplink_tl-wr1043nd-v4
+define Device/tplink_tl-wr1043n-v5
+ $(Device/tplink-safeloader-uimage)
+ ATH_SOC := qca9563
+ IMAGE_SIZE := 15104k
+ DEVICE_TITLE := TP-Link TL-WR1043N v5
+ TPLINK_BOARD_ID := TLWR1043NV5
+ SUPPORTED_DEVICES += tl-wr1043n-v5
+endef
+TARGET_DEVICES += tplink_tl-wr1043n-v5
+
define Device/tplink_tl-wr2543-v1
$(Device/tplink-8mlzma)
ATH_SOC := ar7242