TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <[email protected]>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <[email protected]>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+ compatible = "tplink,eap225-wall-v2", "qca,qca9561";
+ model = "TP-Link EAP225-Wall v2";
+
+ aliases {
+ label-mac-device = ð1;
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ led {
+ label = "LED button";
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: status {
+ label = "tp-link:white:status";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ poe_passthrough {
+ gpio-export,name = "tp-link:poe-passthrough:enable";
+ gpio-export,output = <0>;
+ gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "partition-table";
+ reg = <0x020000 0x010000>;
+ read-only;
+ };
+
+ info: partition@30000 {
+ label = "info";
+ reg = <0x030000 0x010000>;
+ read-only;
+ };
+
+ partition@40000 {
+ compatible = "openwrt,elf";
+ label = "firmware";
+ reg = <0x040000 0xd80000>;
+ };
+
+ partition@dc0000 {
+ label = "config";
+ reg = <0xdc0000 0x030000>;
+ read-only;
+ };
+
+ /* df0000-f30000 undefined in vendor firmware */
+
+ partition@f30000 {
+ label = "mutil-log";
+ reg = <0xf30000 0x080000>;
+ read-only;
+ };
+
+ partition@fb0000 {
+ label = "oops";
+ reg = <0xfb0000 0x040000>;
+ read-only;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&info 0x8>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&info 0x8>;
+};
ucidef_add_switch "switch0" \
"0@eth1" "3:lan:3" "4:lan:2" "5:lan:1" "6@eth0" "2:wan:4" "1:wan:5"
;;
+ tplink,eap225-wall-v2)
+ ucidef_add_switch "switch0" \
+ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+ ;;
tplink,eap245-v3)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:1" "5:lan:2"
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ tplink,eap225-wall-v2)
+ caldata_extract "art" 0x5000 0x2f20
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
+ ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+ ;;
tplink,eap245-v3)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
define Device/tplink-eap2x5
$(Device/tplink-safeloader)
- SOC := qca9563
LOADER_TYPE := elf
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel
KERNEL_INITRAMFS := $$(KERNEL)
pad-extra 128
endef
+define Device/tplink_eap225-wall-v2
+ $(Device/tplink-eap2x5)
+ SOC := qca9561
+ IMAGE_SIZE := 13824k
+ DEVICE_MODEL := EAP225-Wall
+ DEVICE_VARIANT := v2
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+ TPLINK_BOARD_ID := EAP225-WALL-V2
+endef
+TARGET_DEVICES += tplink_eap225-wall-v2
+
define Device/tplink_eap245-v3
$(Device/tplink-eap2x5)
+ SOC := qca9563
IMAGE_SIZE := 14592k
DEVICE_MODEL := EAP245
DEVICE_VARIANT := v3
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the EAP225-Wall v2 */
+ {
+ .id = "EAP225-WALL-V2",
+ .support_list =
+ "SupportList:\r\n"
+ "EAP225-Wall(TP-Link|UN|AC1200-D):2.0\r\n",
+ .support_trail = '\xff',
+ .soft_ver = NULL,
+ .soft_ver_compat_level = 1,
+
+ .partitions = {
+ {"fs-uboot", 0x00000, 0x20000},
+ {"partition-table", 0x20000, 0x02000},
+ {"default-mac", 0x30000, 0x01000},
+ {"support-list", 0x31000, 0x00100},
+ {"product-info", 0x31100, 0x00400},
+ {"soft-version", 0x32000, 0x00100},
+ {"firmware", 0x40000, 0xd80000},
+ {"user-config", 0xdc0000, 0x30000},
+ {"mutil-log", 0xf30000, 0x80000},
+ {"oops", 0xfb0000, 0x40000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system"
+ },
+
/** Firmware layout for the EAP245 v3 */
{
.id = "EAP245-V3",
projects / openwrt / staging / 981213.git / commitdiff