This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.
Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B
Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
fis create -b 0x80060000 -l LeNgTh vmlinux_2
load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
use a hexadecimal calculator to subtract the start from the end in order
to substitute it below, with the leading "0x" to specify it in
hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
reset
10.Wait for the status LED to go solid green
Tested-by: Brian Gonyer <[email protected]>
Signed-off-by: Daniel Gimpelevich <[email protected]>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <[email protected]>
local board="$1"
case "$board" in
+ adtran,bsap1800-v2|\
+ adtran,bsap1840|\
aruba,ap-105|\
avm,fritz300e|\
devolo,dvl1200i|\
local board="$1"
case "$board" in
+ adtran,bsap1800-v2|\
+ adtran,bsap1840)
+ fconfig -s -w -d $(find_mtd_part "RedBoot config") -n boot_cntb -x 0
+ lan_mac=$(mtd_get_mac_binary "Board data" 2)
+ ;;
avm,fritz300e)
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
;;
board=$(board_name)
case "$board" in
+adtran,bsap1800-v2|\
+adtran,bsap1840)
+ ucidef_add_gpio_switch "wifi1_ext_a" "5GHz External Antenna A" "489" "1"
+ ucidef_add_gpio_switch "wifi1_int_a" "5GHz Internal Antenna A" "493"
+ ucidef_add_gpio_switch "wifi1_ext_b" "5GHz External Antenna B" "494" "1"
+ ucidef_add_gpio_switch "wifi1_int_b" "5GHz Internal Antenna B" "495"
+ ucidef_add_gpio_switch "wifi1_ext_c" "5GHz External Antenna C" "496" "1"
+ ucidef_add_gpio_switch "wifi1_int_c" "5GHz Internal Antenna C" "497"
+ ucidef_add_gpio_switch "wifi0_ext_a" "2.4GHz External Antenna A" "505" "1"
+ ucidef_add_gpio_switch "wifi0_int_a" "2.4GHz Internal Antenna A" "506"
+ ucidef_add_gpio_switch "wifi0_ext_b" "2.4GHz External Antenna B" "507" "1"
+ ucidef_add_gpio_switch "wifi0_int_b" "2.4GHz Internal Antenna B" "508"
+ ucidef_add_gpio_switch "wifi0_ext_c" "2.4GHz External Antenna C" "509" "1"
+ ucidef_add_gpio_switch "wifi0_int_c" "2.4GHz Internal Antenna C" "510"
+ ;;
comfast,cf-e5)
ucidef_add_gpio_switch "lte_power" "LTE Power" "14" "1"
ucidef_add_gpio_switch "lte_wakeup" "LTE Wakeup" "11" "1"
board=$(board_name)
case "$board" in
+ adtran,bsap1800-v2|\
+ adtran,bsap1840)
+ macaddr_add "$(mtd_get_mac_binary 'Board data' 2)" $(($PHYNBR * 8 + 1)) > /sys${DEVPATH}/macaddress
+ ;;
iodata,wn-ag300dgr)
# There is no eeprom data for 5 GHz wlan in "art" partition
# which would allow to patch the macaddress
local board=$(board_name)
case "$board" in
+ adtran,bsap1800-v2|\
+ adtran,bsap1840)
+ redboot_fis_do_upgrade "$1" vmlinux_2
+ ;;
jjplus,ja76pf2)
redboot_fis_do_upgrade "$1" linux
;;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar7161_adtran_bsap1880.dtsi"
+
+/ {
+ model = "Adtran/Bluesocket BSAP-1800 v2";
+ compatible = "adtran,bsap1800-v2", "qca,ar7161";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar7161_adtran_bsap1880.dtsi"
+
+/ {
+ model = "Adtran/Bluesocket BSAP-1840";
+ compatible = "adtran,bsap1840", "qca,ar7161";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7100.dtsi"
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-boot = &led_green_status;
+ led-failsafe = &led_yellow_status;
+ led-running = &led_green_status;
+ led-upgrade = &led_yellow_status;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wlan5g {
+ label = "bluesocket:green:wifi5g";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wlan2g {
+ label = "bluesocket:green:wifi2g";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_green_status: green_status {
+ label = "bluesocket:green:status";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led_yellow_status: yellow_status {
+ label = "bluesocket:yellow:status";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0x1>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ecoscentric,redboot-fis-partitions";
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
endef
TARGET_DEVICES += 8dev_carambola2
+define Device/adtran_bsap1880
+ ATH_SOC := ar7161
+ DEVICE_VENDOR := Adtran/Bluesocket
+ DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig
+ KERNEL := kernel-bin | append-dtb | lzma
+ KERNEL_INITRAMFS := kernel-bin | append-dtb
+ IMAGE_SIZE := 11200k
+ IMAGES += kernel.bin rootfs.bin
+ IMAGE/kernel.bin := append-kernel | pad-to $$$$(BLOCKSIZE)
+ IMAGE/rootfs.bin := append-rootfs | pad-rootfs
+ IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+
+define Device/adtran_bsap1800-v2
+ $(Device/adtran_bsap1880)
+ DEVICE_MODEL := BSAP-1800
+ DEVICE_VARIANT := v2
+endef
+TARGET_DEVICES += adtran_bsap1800-v2
+
+define Device/adtran_bsap1840
+ $(Device/adtran_bsap1880)
+ DEVICE_MODEL := BSAP-1840
+endef
+TARGET_DEVICES += adtran_bsap1840
+
define Device/aruba_ap-105
ATH_SOC := ar7161
DEVICE_VENDOR := Aruba
projects / openwrt / staging / lynxis.git / commitdiff