--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+ model = "Aruba AP-315";
+ compatible = "aruba,ap-315", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ stdout-path = "serial0:9600n8";
+ };
+
+ soc {
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ status_green {
+ label = "ap-315:green:status";
+ gpios = <&qcom_pinmux 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ status_amber {
+ label = "ap-315:amber:status";
+ gpios = <&qcom_pinmux 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ status_red {
+ label = "ap-315:red:status";
+ gpios = <&qcom_pinmux 30 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan_green {
+ label = "ap-315:green:wlan";
+ gpios = <&qcom_pinmux 30 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan_red {
+ label = "ap-315:red:wlan";
+ gpios = <&qcom_pinmux 30 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&qcom_pinmux {
+ /*
+ * In addition to the Pins listed below,
+ * the following GPIOs have "features":
+ *
+ * 27 - out - active low to force HW reset
+ * 26 - out - active low to reset TPM
+ * 67 - out - active low to reset PHY0
+ * 68 - out - active low to reset PHY1 (?)
+ * 3 - out - active low to reset PCIE1
+ * 48 - out - active low to reset PCIE2
+ * 62 - out - pulse to set warm reset status
+ * 52 - out - pulse to reset watchdog status flipflop
+ * 51 - out - active low to enable USB port power
+ * 2 - out - active low to reset BLE radio
+ * 7 - out - active high to disable external watchdog
+ *
+ * 59 - in - active high when PoE powered
+ * 8 - in - active high when DC powered
+ * 64 - in - active low when cold H/W reset
+ * 65 - in - active high when external watchdog reset
+ * 63 - in - active low when USB over-current
+ * 53 - in - phy0 interrupt line
+ * 54 - in - phy1 interrupt line (?)
+ *
+ * Note that these values originate from Aruba's documentation
+ */
+ i2c2_pins: i2c2_pinmux {
+ pins = "gpio24", "gpio25";
+ function = "gsbi2";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ button_pins: button_pins {
+ mux {
+ pins = "gpio9";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio28", "gpio29", "gpio30", "gpio31", "gpio32";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
+
+&gsbi2 {
+ i2c@124a0000 {
+ status = "okay";
+ }
+}
+
+&gsbi4 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi4_serial {
+ status = "okay";
+};
+
+&gsbi5 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_SPI>;
+
+ spi4: spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "mibib";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "sbl2";
+ reg = <0x40000 0x40000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "sbl3";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "ddrconfig";
+ reg = <0x100000 0x10000>;
+ read-only;
+ };
+
+ partition@110000 {
+ label = "ssd";
+ reg = <0x110000 0x10000>;
+ read-only;
+ };
+
+ partition@120000 {
+ label = "tz";
+ reg = <0x120000 0x80000>;
+ read-only;
+ };
+
+ partition@1a0000 {
+ label = "rpm";
+ reg = <0x1a0000 0x80000>;
+ read-only;
+ };
+
+ partition@780000 {
+ label = "appsbl";
+ reg = <0x220000 0x100000>;
+ read-only;
+ };
+
+ partition@320000 {
+ label = "appsblenv";
+ reg = <0x320000 0x10000>;
+ read-only;
+ };
+
+ partition@330000 {
+ label = "art";
+ reg = <0x330000 0x40000>;
+ read-only;
+ };
+
+ partition@370000 {
+ label = "ap_pds";
+ reg = <0x370000 0x10000>;
+ };
+
+ partition@380000 {
+ label = "ap_cd";
+ reg = <0x380000 0x10000>;
+ };
+
+ partition@390000 {
+ label = "manu_info";
+ reg = <0x390000 0x10000>;
+ };
+
+ partition@3a0000 {
+ label = "ap_fc";
+ reg = <0x3a0000 0x10000>;
+ };
+
+ partition@3b0000 {
+ label = "ap_os_ss";
+ reg = <0x3b0000 0x50000>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&nand {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ cs0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /* 'aos0' in Aruba firmware */
+ label = "aos0";
+ reg = <0x0 0x2000000>;
+ read-only;
+ };
+
+ partition@2000000 {
+ /* 'aos1' in Aruba firmware */
+ label = "ubi";
+ reg = <0x2000000 0x2000000>;
+ };
+
+ partition@4000000 {
+ label = "aruba-ubifs";
+ reg = <0x4000000 0x4000000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&gmac2 {
+ status = "okay";
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy5>;
+
+ qcom,id = <1>;
+};
projects / openwrt / staging / blocktrron.git / commitdiff