COMFAST CF-WR632AX is a compact/travel (123.4 mm * 88.7 mm * 34 mm)
wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz
- RAM : DDR3 512 MiB
- Flash : SPI-NAND 128 MiB (Winbond)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MU-MIMO (2x 5 dBi antennas)
- 5 GHz : a/n/ac/ax, MU-MIMO (2x 5 dBi antennas)
- Ethernet :
- LAN x1 : 10/100/1000 Mbps (MT7981 internal PHY)
- WAN x1 : 10/100/1000/2500 Mbps (Maxlinear GPY211C)
- USB x1 : 3.0
- UART : through-hole on PCB
- assignment : (RX), (TX), (GND), [VCC]
- settings : 115200n8
- Buttons x1 : Reset
- LEDs x3 : Status (Blue, Green, Red)
- Fan x1 : PWM, 4-wire, 5 V, 0.3 A, 45 mm * 10 mm
- Power : 5 VDC, 3 A, Type-C
Flash instructions
------------------
WebUI Method:
1. Install the *squashfs-sysupgrade.bin image using the stock WebUI
update page.
2. Press and hold the reset button after reboot
to wipe the stock config.
SSH Method:
1. Import stock firmware settings from backup file
github.com/andros-ua/owrt-misc/blob/main/cf-wr632ax/backup.file
Note: WebUI password will be reset to admin1234 after import.
2. Connect via SSH using root:openwrt credentials.
3. Upload the *squashfs-sysupgrade.bin image.
4. Use the command: sysupgrade -n
All checks should pass.
Return to stock
---------------
Flash a stock firmware
using the OpenWrt sysupgrade method.
Recovery
--------
Power on the router while holding the Reset button until
the LED flashes 5 times.
The U-Boot Flash WebUI will be available at http://192.168.1.1
or
Connect UART and use the U-Boot menu to flash the firmware image
or boot an OpenWrt initramfs image.
OpenWrt U-Boot flash instructions
---------------------------------
1. Flash ordinary OpenWrt image.
2. Login into the device and backup everything, especially 'Factory' part.
3. Unlock mtd partitions:
apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
ip 192.168.1.254 mask 255.255.255.0
6. Serve OpenWrt initramfs image using TFTP server.
7. Reboot device, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
MAC Addresses:
----------------------------------------------------------
| Interface | MAC | Source |
---------------|-------------------|----------------------
| WAN (label) | 40:A5:EF:xx:xx:xx | Factory, 0xe000 |
| LAN | 40:A5:EF:xx:xx:xx | Factory, 0xe000 + 1 |
| WLAN 2.4 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x4 |
| WLAN 5 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x8000 |
----------------------------------------------------------
Signed-off-by: Andrii Kuiukoff <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20382
Signed-off-by: Hauke Mehrtens <[email protected]>
DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr4
endef
+define U-Boot/mt7981_comfast_cf-wr632ax
+ NAME:=COMFAST CF-WR632AX
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=comfast_cf-wr632ax-ubootmod
+ UBOOT_CONFIG:=mt7981_comfast_cf-wr632ax
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=spim-nand
+ BL2_SOC:=mt7981
+ BL2_DDRTYPE:=ddr3
+ DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
+endef
+
define U-Boot/mt7981_cudy_tr3000-v1
NAME:=Cudy TR3000 v1
BUILD_SUBTARGET:=filogic
mt7981_cmcc_rax3000m-emmc-ddr4 \
mt7981_cmcc_rax3000m-nand-ddr3 \
mt7981_cmcc_rax3000m-nand-ddr4 \
+ mt7981_comfast_cf-wr632ax \
mt7981_cudy_tr3000-v1 \
mt7981_gatonetworks_gdsp \
mt7981_glinet_gl-mt2500 \
--- /dev/null
+--- /dev/null
++++ b/arch/arm/dts/mt7981-comfast-cf-wr632ax.dts
+@@ -0,0 +1,153 @@
++// SPDX-License-Identifier: GPL-2.0-or-later
++
++/dts-v1/;
++#include "mt7981.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/input/linux-event-codes.h>
++
++/ {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ model = "COMFAST CF-WR632AX";
++ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
++
++ chosen {
++ stdout-path = &uart0;
++ tick-timer = &timer0;
++ };
++
++ memory@40000000 {
++ device_type = "memory";
++ reg = <0x40000000 0x20000000>;
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ button-reset {
++ label = "reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ led_status_blue: led-0 {
++ label = "blue:status";
++ gpios = <&pio 8 GPIO_ACTIVE_LOW>;
++ default-state = "off";
++ };
++
++ led_status_green: led-1 {
++ label = "green:status";
++ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
++ default-state = "off";
++ };
++
++ led_status_red: led-2 {
++ label = "red:status";
++ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
++ default-state = "on";
++ };
++ };
++};
++
++ð {
++ status = "okay";
++ mediatek,gmac-id = <1>;
++ phy-mode = "gmii";
++ phy-handle = <&phy0>;
++
++ mdio {
++ phy0: ethernet-phy@0 {
++ compatible = "ethernet-phy-id03a2.9461";
++ reg = <0x0>;
++ phy-mode = "gmii";
++ };
++ };
++};
++
++&pio {
++ spi_flash_pins: spi0-pins-func-1 {
++ mux {
++ function = "flash";
++ groups = "spi0", "spi0_wp_hold";
++ };
++
++ conf-pu {
++ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
++ drive-strength = <MTK_DRIVE_4mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
++ };
++
++ conf-pd {
++ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
++ drive-strength = <MTK_DRIVE_4mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
++ };
++ };
++};
++
++&spi0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_flash_pins>;
++ status = "okay";
++ must_tx;
++ enhance_timing;
++ dma_ext;
++ ipm_design;
++ support_quad;
++ tick_dly = <2>;
++ sample_sel = <0>;
++
++ spi_nand@0 {
++ compatible = "spi-nand";
++ reg = <0>;
++ spi-max-frequency = <52000000>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition@0 {
++ label = "bl2";
++ reg = <0x0 0x100000>;
++ };
++
++ partition@100000 {
++ label = "u-boot-env";
++ reg = <0x100000 0x80000>;
++ };
++
++ partition@180000 {
++ label = "factory";
++ reg = <0x180000 0x200000>;
++ };
++
++ partition@380000 {
++ label = "fip";
++ reg = <0x380000 0x200000>;
++ };
++
++ partition@580000 {
++ label = "ubi";
++ reg = <0x580000 0x7a80000>;
++ compatible = "linux,ubi";
++ };
++ };
++ };
++};
++
++&uart0 {
++ mediatek,force-highspeed;
++ status = "okay";
++};
++
++&watchdog {
++ status = "disabled";
++};
+--- /dev/null
++++ b/configs/mt7981_comfast_cf-wr632ax_defconfig
+@@ -0,0 +1,107 @@
++CONFIG_ARM=y
++CONFIG_SYS_HAS_NONCACHED_MEMORY=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7981-comfast-cf-wr632ax"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_TARGET_MT7981=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_FIT=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981-comfast-cf-wr632ax.dtb"
++CONFIG_LOGLEVEL=7
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_LOG=y
++# CONFIG_BOARD_INIT is not set
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_PROMPT="MT7981> "
++CONFIG_CMD_CPU=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_LINK_LOCAL=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_UUID=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_UBI=y
++CONFIG_ENV_REDUNDANT=y
++CONFIG_ENV_UBI_PART="ubi"
++CONFIG_ENV_UBI_VOLUME="ubootenv"
++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
++CONFIG_ENV_RELOC_GD_ENV_ADDR=y
++CONFIG_ENV_USE_DEFAULT_ENV_TEXT_FILE=y
++CONFIG_ENV_DEFAULT_ENV_TEXT_FILE="defenvs/comfast_cf-wr632ax_env"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_NETCONSOLE=y
++CONFIG_USE_IPADDR=y
++CONFIG_IPADDR="192.168.1.1"
++CONFIG_USE_SERVERIP=y
++CONFIG_SERVERIP="192.168.1.254"
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_CLK=y
++CONFIG_GPIO_HOG=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++# CONFIG_MMC is not set
++CONFIG_MTD=y
++CONFIG_DM_MTD=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_PHY_FIXED=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PHY=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7981=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPIM=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
+--- /dev/null
++++ b/defenvs/comfast_cf-wr632ax_env
+@@ -0,0 +1,54 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
++bootconf=config-1
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-squashfs-sysupgrade.itb
++bootled_pwr=red:status
++bootled_rec=blue:status
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) )
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
acer,predator-w6x-ubootmod|\
asus,zenwifi-bt8-ubootmod|\
cmcc,a10-ubootmod|\
+comfast,cf-wr632ax-ubootmod|\
cudy,tr3000-v1-ubootmod|\
h3c,magic-nx30-pro|\
jcg,q30-pro|\
;;
asiarf,ap7986-003|\
cetron,ct3003|\
+comfast,cf-wr632ax|\
edgecore,eap111|\
netgear,wax220|\
zbtlink,zbt-z8102ax|\
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "mt7981b.dtsi"
+
+/ {
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_status_red;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_green;
+ serial0 = &uart0;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_blue: blue {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_green: green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_red: red {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ label = "wan";
+ phy-mode = "2500base-x";
+ phy-handle = <&phy5>;
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_e000 0>;
+ };
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ label = "lan";
+ phy-mode = "gmii";
+ phy-handle = <&int_gbe_phy>;
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_e000 1>;
+ };
+};
+
+&fan {
+ pwms = <&pwm 0 10000>;
+ status = "okay";
+};
+
+&mdio_bus {
+ reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <600>;
+ reset-post-delay-us = <20000>;
+
+ phy5: phy@5 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <5>;
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+
+ pwm0_pin: pwm0-pin-g0 {
+ mux {
+ function = "pwm";
+ groups = "pwm0_0";
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand: spi-nand@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "BL2";
+ reg = <0x00000 0x0100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "u-boot-env";
+ reg = <0x0100000 0x0080000>;
+ read-only;
+ };
+
+ factory: partition@180000 {
+ label = "Factory";
+ reg = <0x180000 0x0200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom@0 {
+ reg = <0x0 0x1000>;
+ };
+
+ macaddr_factory_e000: macaddr@e000 {
+ compatible = "mac-base";
+ reg = <0xe000 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ macaddr_factory_4: macaddr@4 {
+ compatible = "mac-base";
+ reg = <0x4 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ macaddr_factory_8000: macaddr@8000 {
+ compatible = "mac-base";
+ reg = <0x8000 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition@380000 {
+ label = "FIP";
+ reg = <0x380000 0x0200000>;
+ read-only;
+ };
+
+ ubi: partition@580000 {
+ label = "ubi";
+ compatible = "linux,ubi";
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&xhci {
+ status = "okay";
+};
+
+&wifi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+ status = "okay";
+
+ band@0 {
+ reg = <0>;
+ nvmem-cells = <&macaddr_factory_4 0>;
+ nvmem-cell-names = "mac-address";
+ };
+
+ band@1 {
+ reg = <1>;
+ nvmem-cells = <&macaddr_factory_8000 0>;
+ nvmem-cell-names = "mac-address";
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7981b-comfast-cf-wr632ax-common.dtsi"
+
+/ {
+ model = "COMFAST CF-WR632AX (OpenWrt U-Boot layout)";
+ compatible = "comfast,cf-wr632ax-ubootmod", "mediatek,mt7981";
+};
+
+&chosen {
+ bootargs = "root=/dev/fit0 rootwait";
+ rootdisk = <&ubi_rootdisk>;
+};
+
+&ubi {
+ reg = <0x580000 0x7a80000>;
+
+ volumes {
+ ubi_rootdisk: ubi-volume-fit {
+ volname = "fit";
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7981b-comfast-cf-wr632ax-common.dtsi"
+
+/ {
+ model = "COMFAST CF-WR632AX";
+ compatible = "comfast,cf-wr632ax", "mediatek,mt7981";
+};
+
+&spi_nand {
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+};
+
+&ubi {
+ reg = <0x580000 0x4000000>;
+};
dlink,aquila-pro-ai-m60-a1)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet
;;
+ comfast,cf-wr632ax|\
+ comfast,cf-wr632ax-ubootmod|\
keenetic,kn-3911|\
smartrg,sdg-8622|\
smartrg,sdg-8632|\
bananapi,bpi-r4-lite|\
cmcc,a10-ubootmod|\
cmcc,rax3000m|\
+ comfast,cf-wr632ax-ubootmod|\
cudy,tr3000-v1-ubootmod|\
gatonetworks,gdsp|\
h3c,magic-nx30-pro|\
bananapi,bpi-r4-lite|\
cmcc,a10-ubootmod|\
cmcc,rax3000m|\
+ comfast,cf-wr632ax-ubootmod|\
cudy,tr3000-v1-ubootmod|\
gatonetworks,gdsp|\
h3c,magic-nx30-pro|\
endef
TARGET_DEVICES += comfast_cf-e393ax
+define Device/comfast_cf-wr632ax-common
+ DEVICE_VENDOR := COMFAST
+ DEVICE_MODEL := CF-WR632AX
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_IN_UBI := 1
+endef
+
+define Device/comfast_cf-wr632ax
+ DEVICE_DTS := mt7981b-comfast-cf-wr632ax
+ IMAGE_SIZE := 65536k
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ SUPPORTED_DEVICES += cf-wr632ax
+ $(call Device/comfast_cf-wr632ax-common)
+endef
+TARGET_DEVICES += comfast_cf-wr632ax
+
+define Device/comfast_cf-wr632ax-ubootmod
+ DEVICE_VARIANT := (OpenWrt U-Boot layout)
+ DEVICE_DTS := mt7981b-comfast-cf-wr632ax-ubootmod
+ UBOOTENV_IN_UBI := 1
+ IMAGES := sysupgrade.itb
+ KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+ KERNEL := kernel-bin | gzip
+ KERNEL_INITRAMFS := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+ IMAGE/sysupgrade.itb := append-kernel | \
+ fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
+ ARTIFACTS := preloader.bin bl31-uboot.fip
+ ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
+ ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot comfast_cf-wr632ax
+ $(call Device/comfast_cf-wr632ax-common)
+endef
+TARGET_DEVICES += comfast_cf-wr632ax-ubootmod
+
define Device/confiabits_mt7981
DEVICE_VENDOR := Confiabits
DEVICE_MODEL := MT7981
projects / openwrt / staging / blocktrron.git / commitdiff