ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1"
ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0"
;;
-hpe,msm460)
- ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
- ;;
esac
board_config_flush
aerohive,hiveap-330)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
-hpe,msm460)
- ucidef_set_interface_lan "eth0"
- ;;
ocedo,panda)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
local board=$(board_name)
case "$board" in
- hpe,msm460|\
ocedo,panda|\
sophos,red-15w-rev1|\
watchguard,firebox-t10)
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later or MIT
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/include/ "fsl/p1020si-pre.dtsi"
-/ {
- model = "Hewlett-Packard MSM460";
- compatible = "hpe,msm460";
-
- aliases {
- led-boot = &system_green;
- led-failsafe = &system_green;
- led-running = &system_green;
- led-upgrade = &system_green;
- };
-
- chosen {
- /* Needed for initramfs */
- bootargs-override = "console=ttyS0,115200 ubi.mtd=3,2048";
- };
-
- memory {
- device_type = "memory";
- };
-
- lbc: localbus@ffe05000 {
- reg = <0 0xffe05000 0 0x1000>;
- ranges = <0x0 0x0 0x0 0xec000000 0x04000000
- 0x1 0x0 0x0 0xff800000 0x00040000
- 0x2 0x0 0x0 0xffa00000 0x00020000
- 0x3 0x0 0x0 0xffb00000 0x00020000>;
-
- nand@1,0 {
- compatible = "fsl,p1020-fcm-nand", "fsl,elbc-fcm-nand";
- reg = <0x1 0x0 0x40000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- reg = <0x0 0x100000>;
- label = "uboot";
- };
-
- partition@a0000 {
- reg = <0x100000 0x60000>;
- label = "uboot-env0";
- };
-
- partition@c0000 {
- reg = <0x160000 0x60000>;
- label = "uboot-env1";
- };
-
- partition@100000 {
- reg = <0x1c0000 0x4800000>;
- label = "ubi";
- };
- };
- };
- };
-
- soc: soc@ffe00000 {
- ranges = <0x0 0x0 0xffe00000 0x100000>;
-
- i2c@3000 {
- status = "disabled";
- };
-
- gpio0: gpio-controller@fc00 {
- };
-
- mdio@24000 {
- phy0: ethernet-phy@0 {
- reg = <0x0>;
- reset-gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <10000>;
- };
- };
-
- enet0: ethernet@b0000 {
- phy-connection-type = "rgmii-id";
- phy-handle = <&phy0>;
- };
-
- enet1: ethernet@b1000 {
- status = "disabled";
- };
-
- enet2: ethernet@b2000 {
- status = "disabled";
- };
-
- usb@22000 {
- status = "disabled";
- };
-
- usb@23000 {
- status = "disabled";
- };
- };
-
- pci0: pcie@ffe09000 {
- ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- reg = <0 0xffe09000 0 0x1000>;
- pcie@0 {
- ranges = <0x2000000 0x0 0xa0000000
- 0x2000000 0x0 0xa0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
- pci1: pcie@ffe0a000 {
- reg = <0 0xffe0a000 0 0x1000>;
- ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
- pcie@0 {
- ranges = <0x2000000 0x0 0x80000000
- 0x2000000 0x0 0x80000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- system_green: power {
- gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
- label = "green:power";
- default-state = "on";
- };
-
- lan {
- gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
- label = "green:lan";
- };
-
- radio1 {
- gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
- label = "green:radio1";
- linux,default-trigger = "phy1tpt";
- };
-
- radio2 {
- gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
- label = "green:radio2";
- };
- };
-
- buttons {
- compatible = "gpio-keys";
-
- reset {
- label = "reset-btn";
- gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
- linux,code = <KEY_RESTART>;
- };
- };
-};
-/include/ "fsl/p1020si-post.dtsi"
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later
-
-/*
- * HPE MSM460 Board Setup
- *
- *
- * Based on:
- * mpc85xx_rdb.c:
- * MPC85xx RDB Board Setup
- * Copyright 2013 Freescale Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/stddef.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/of_platform.h>
-
-#include <asm/time.h>
-#include <asm/machdep.h>
-#include <asm/pci-bridge.h>
-#include <mm/mmu_decl.h>
-#include <asm/prom.h>
-#include <asm/udbg.h>
-#include <asm/mpic.h>
-
-#include <sysdev/fsl_soc.h>
-#include <sysdev/fsl_pci.h>
-#include "smp.h"
-
-#include "mpc85xx.h"
-
-void __init msm_pic_init(void)
-{
- struct mpic *mpic;
-
- mpic = mpic_alloc(NULL, 0,
- MPIC_BIG_ENDIAN |
- MPIC_SINGLE_DEST_CPU,
- 0, 256, " OpenPIC ");
-
- BUG_ON(mpic == NULL);
- mpic_init(mpic);
-}
-
-/*
- * Setup the architecture
- */
-static void __init msm_setup_arch(void)
-{
- if (ppc_md.progress)
- ppc_md.progress("msm_setup_arch()", 0);
-
- mpc85xx_smp_init();
-
- fsl_pci_assign_primary();
-
- pr_info("MSM460 board from HPE\n");
-}
-
-machine_arch_initcall(msm, mpc85xx_common_publish_devices);
-
-/*
- * Called very early, device-tree isn't unflattened
- */
-static int __init msm_probe(void)
-{
- if (of_machine_is_compatible("hpe,msm460"))
- return 1;
- return 0;
-}
-
-define_machine(msm) {
- .name = "P1020 RDB",
- .probe = msm_probe,
- .setup_arch = msm_setup_arch,
- .init_IRQ = msm_pic_init,
-#ifdef CONFIG_PCI
- .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
- .pcibios_fixup_phb = fsl_pcibios_fixup_phb,
-#endif
- .get_irq = mpic_get_irq,
- .calibrate_decr = generic_calibrate_decr,
- .progress = udbg_progress,
-};
endef
TARGET_DEVICES += extreme-networks_ws-ap3825i
-define Device/hpe_msm460
- DEVICE_VENDOR := Hewlett-Packard
- DEVICE_MODEL := MSM460
- KERNEL = kernel-bin | lzma | fit lzma $(KDIR)/image-$$(DEVICE_DTS).dtb
- IMAGES := sysupgrade.bin
- IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
-endef
-TARGET_DEVICES += hpe_msm460
-
define Device/ocedo_panda
DEVICE_VENDOR := OCEDO
DEVICE_MODEL := Panda
IMAGE/fdt.bin := append-dtb
endef
TARGET_DEVICES += ocedo_panda
+
CONFIG_HAVE_RCU_TABLE_FREE=y
CONFIG_HIVEAP_330=y
CONFIG_PANDA=y
-CONFIG_MSM460=y
CONFIG_I2C_CHARDEV=y
CONFIG_LEDS_LP5521=y
CONFIG_LEDS_LP55XX_COMMON=y
+++ /dev/null
---- a/arch/powerpc/platforms/85xx/Kconfig
-+++ b/arch/powerpc/platforms/85xx/Kconfig
-@@ -92,6 +92,17 @@ config WS_AP3825I
- This board is a Concurrent Dual-Band wireless access point with a
- Freescale P1020 SoC.
-
-+config MSM460
-+ bool "HPE MSM460"
-+ select DEFAULT_UIMAGE
-+ select ARCH_REQUIRE_GPIOLIB
-+ select GPIO_MPC8XXX
-+ help
-+ This option enables support for the HPE MSM460 board.
-+
-+ This board is a Concurrent Dual-Band wireless access point with a
-+ Freescale P1020 SoC.
-+
- config MPC8540_ADS
- bool "Freescale MPC8540 ADS"
- select DEFAULT_UIMAGE
---- a/arch/powerpc/platforms/85xx/Makefile
-+++ b/arch/powerpc/platforms/85xx/Makefile
-@@ -28,6 +28,7 @@ obj-$(CONFIG_PANDA) += panda.o
- obj-$(CONFIG_TWR_P102x) += twr_p102x.o
- obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
- obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o
-+obj-$(CONFIG_MSM460) += msm460.o
- obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
- obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
- obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o
+++ /dev/null
---- a/arch/powerpc/platforms/85xx/Kconfig
-+++ b/arch/powerpc/platforms/85xx/Kconfig
-@@ -71,6 +71,17 @@ config PANDA
- This board is a Concurrent Dual-Band wireless access point with a
- Freescale P1020 SoC.
-
-+config MSM460
-+ bool "HPE MSM460"
-+ select DEFAULT_UIMAGE
-+ select ARCH_REQUIRE_GPIOLIB
-+ select GPIO_MPC8XXX
-+ help
-+ This option enables support for the HPE MSM460 board.
-+
-+ This board is a Concurrent Dual-Band wireless access point with a
-+ Freescale P1020 SoC.
-+
- config MPC8540_ADS
- bool "Freescale MPC8540 ADS"
- select DEFAULT_UIMAGE
---- a/arch/powerpc/platforms/85xx/Makefile
-+++ b/arch/powerpc/platforms/85xx/Makefile
-@@ -26,6 +26,7 @@ obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
- obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
- obj-$(CONFIG_PANDA) += panda.o
- obj-$(CONFIG_TWR_P102x) += twr_p102x.o
-+obj-$(CONFIG_MSM460) += msm460.o
- obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
- obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
- obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o
projects / openwrt / staging / blocktrron.git / commitdiff