TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <[email protected]>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <[email protected]>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7628an_tplink_8m-split-uboot.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "tplink,archer-c20-v5", "mediatek,mt7628an-soc";
+ model = "TP-Link Archer C20 v5";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "archer-c20-v5:green:power";
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "archer-c20-v5:green:wlan2g";
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "archer-c20-v5:green:wlan5g";
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ lan {
+ label = "archer-c20-v5:green:lan";
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_green {
+ label = "archer-c20-v5:green:wan";
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_orange {
+ label = "archer-c20-v5:orange:wan";
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "archer-c20-v5:green:wps";
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ ralink,group = "i2s", "gpio", "refclk", "p0led_an", "p1led_an",
+ "p2led_an", "p3led_an", "p4led_an", "wdt";
+ ralink,function = "gpio";
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&radio 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ mtd-mac-address = <&rom 0xf100>;
+ mtd-mac-address-increment = <(-1)>;
+ };
+};
endef
TARGET_DEVICES += tplink_archer-c20-v4
+define Device/tplink_archer-c20-v5
+ $(Device/tplink)
+ IMAGE_SIZE := 7616k
+ DEVICE_MODEL := Archer C20
+ DEVICE_VARIANT := v5
+ TPLINK_FLASHLAYOUT := 8MSUmtk
+ TPLINK_HWID := 0xc200005
+ TPLINK_HWREV := 0x1
+ TPLINK_HWREVADD := 0x5
+ TPLINK_HVERSION := 3
+ DEVICE_PACKAGES := kmod-mt76x0e
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += tplink_archer-c20-v5
+
define Device/tplink_archer-c50-v3
$(Device/tplink)
IMAGE_SIZE := 7808k
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt"
;;
-tplink,archer-c20-v4)
+tplink,archer-c20-v4|\
+tplink,archer-c20-v5)
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e"
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
;;
hiwifi,hc5861b|\
skylab,skw92a|\
tplink,archer-c20-v4|\
+ tplink,archer-c20-v5|\
tplink,archer-c50-v3|\
tplink,archer-c50-v4|\
tplink,tl-mr3420-v5|\
tplink,tl-wr842n-v5)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0xf100)" 1)
;;
+ tplink,archer-c20-v5|\
tplink,archer-c50-v4)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary rom 0xf100)" 1)
;;
}
default_do_upgrade "$1"
;;
+ tplink,archer-c20-v5|\
tplink,archer-c50-v4)
MTD_ARGS="-t romfile"
default_do_upgrade "$1"
projects / openwrt / staging / xback.git / commitdiff