ath79: support for TP-Link EAP225 v4

This model is almost identical to the EAP225 v3.
Major difference is the RTL8211FS PHY Chipset.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE

Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
      Do NOT bridge R230.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.

Signed-off-by: Sven Hauer <[email protected]>

diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts
new file mode 100644 (file)
index 0000000..ae27ff7
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_tplink_eap2x5-1port.dtsi"
+
+/ {
+       compatible = "tplink,eap225-v4", "qca,qca9563";
+       model = "TP-Link EAP225 v4";
+
+       aliases {
+               led-boot = &led_status_green;
+               led-failsafe = &led_status_amber;
+               led-running = &led_status_green;
+               led-upgrade = &led_status_amber;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_status_green: status_green {
+                       label = "green:status";
+                       gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+                       default-state = "on";
+               };
+
+               led_status_amber: status_amber {
+                       label = "amber:status";
+                       gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+               };
+       };
+};
+
+&art {
+       precalibration_ath10k: pre-calibration@5000 {
+               reg = <0x5000 0x2f20>;
+       };
+};
+
+&eth0 {
+       phy-handle = <&phy6>;
+       phy-mode = "sgmii";
+};
+
+&mdio0 {
+       phy6: ethernet-phy@6 {
+               reg = <6>;
+       };
+};
+
+&pcie {
+       wifi@0,0 {
+               compatible = "qcom,ath10k";
+               reg = <0 0 0 0 0>;
+
+               mac-address-increment = <1>;
+
+               nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>;
+               nvmem-cell-names = "mac-address", "pre-calibration";
+       };
+};

diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 42ab19b47a6f9d01abaeaf7c1a0a61522da6a69b..7ba39c4c4965ddc82061a7b938f8fd4312f50e35 100644 (file)
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -79,6 +79,7 @@ ath79_setup_interfaces()
        tplink,eap225-outdoor-v3|\
        tplink,eap225-v1|\
        tplink,eap225-v3|\
+       tplink,eap225-v4|\
        tplink,eap245-v1|\
        tplink,re350k-v1|\
        tplink,re355-v1|\

diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index ffe999660acb7534110e7944a1b677565e01ac0d..6d9ba2cd40342744ce6d86c2a23b349367b53220 100644 (file)
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -434,6 +434,17 @@ define Device/tplink_eap225-v3
 endef
 TARGET_DEVICES += tplink_eap225-v3
 
+define Device/tplink_eap225-v4
+  $(Device/tplink-eap2x5)
+  SOC := qca9563
+  IMAGE_SIZE := 13824k
+  DEVICE_MODEL := EAP225
+  DEVICE_VARIANT := v4
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+  TPLINK_BOARD_ID := EAP225-V3
+endef
+TARGET_DEVICES += tplink_eap225-v4
+
 define Device/tplink_eap225-wall-v2
   $(Device/tplink-eap2x5)
   SOC := qca9561