DEPENDS:=+trusted-firmware-a-mt7986-sdmmc-ddr4
endef
+define U-Boot/mt7986_acer_predator-w6x
+ NAME:=Acer Predator Connect W6x
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=acer_predator-w6x-ubootmod
+ UBOOT_CONFIG:=mt7986_acer_predator-w6x
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=spim-nand
+ BL2_SOC:=mt7986
+ BL2_DDRTYPE:=ddr4
+ DEPENDS:=+trusted-firmware-a-mt7986-spim-nand-ddr4
+endef
+
define U-Boot/mt7986_bananapi_bpi-r3-emmc
NAME:=BananaPi BPi-R3
BUILD_SUBTARGET:=filogic
mt7981_snr_snr-cpe-ax2 \
mt7981_xiaomi_mi-router-ax3000t \
mt7981_xiaomi_mi-router-wr30u \
+ mt7986_acer_predator-w6x \
mt7986_bananapi_bpi-r3-emmc \
mt7986_bananapi_bpi-r3-sdmmc \
mt7986_bananapi_bpi-r3-snand \
--- /dev/null
+--- /dev/null
++++ b/arch/arm/dts/mt7986a-acer_predator-w6x.dts
+@@ -0,0 +1,150 @@
++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
++
++/dts-v1/;
++#include <dt-bindings/input/linux-event-codes.h>
++#include "mt7986.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++
++/ {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ model = "Acer Predator Connect W6x";
++ compatible = "mediatek,mt7986", "mediatek,mt7986-sd-rfb";
++
++ chosen {
++ stdout-path = &uart0;
++ tick-timer = &timer0;
++ };
++
++ memory@40000000 {
++ device_type = "memory";
++ reg = <0x40000000 0x20000000>;
++ };
++
++ keys {
++ compatible = "gpio-keys";
++
++ factory {
++ label = "reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
++ };
++
++ wps {
++ label = "wps";
++ linux,code = <KEY_WPS_BUTTON>;
++ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++ð {
++ status = "okay";
++ mediatek,gmac-id = <0>;
++ phy-mode = "2500base-x";
++ mediatek,switch = "mt7531";
++ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
++
++ fixed-link {
++ speed = <2500>;
++ full-duplex;
++ };
++};
++
++&pio {
++ spic_pins: spi1-pins-func-1 {
++ mux {
++ function = "spi";
++ groups = "spi1_2";
++ };
++ };
++
++ spi_flash_pins: spi0-pins-func-1 {
++ mux {
++ function = "flash";
++ groups = "spi0", "spi0_wp_hold";
++ };
++
++ conf-pu {
++ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
++ };
++
++ conf-pd {
++ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
++ };
++ };
++};
++
++&spi0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_flash_pins>;
++ status = "okay";
++ must_tx;
++ enhance_timing;
++ dma_ext;
++ ipm_design;
++ support_quad;
++ tick_dly = <1>;
++ sample_sel = <0>;
++ pinctrl-names = "default";
++
++ spi_nand@0 {
++ compatible = "spi-nand";
++ reg = <0>;
++ spi-max-frequency = <52000000>;
++ spi-tx-bus-width = <4>;
++ spi-rx-bus-width = <4>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition@0 {
++ label = "bl2";
++ reg = <0x0 0x100000>;
++ };
++
++ partition@100000 {
++ label = "u-boot-env";
++ reg = <0x100000 0x80000>;
++ };
++
++ partition@180000 {
++ label = "factory";
++ reg = <0x180000 0x200000>;
++ };
++
++ partition@380000 {
++ label = "fip";
++ reg = <0x380000 0x200000>;
++ };
++
++ partition@580000 {
++ label = "prod";
++ reg = <0x580000 0x20000>;
++ read-only;
++ };
++
++ partition@600000 {
++ label = "ubi";
++ reg = <0x600000 0xD200000>;
++ };
++ };
++ };
++};
++
++&uart0 {
++ mediatek,force-highspeed;
++ status = "okay";
++};
++
++&watchdog {
++ status = "disabled";
++};
+--- /dev/null
++++ b/configs/mt7986_acer_predator-w6x_defconfig
+@@ -0,0 +1,105 @@
++CONFIG_ARM=y
++CONFIG_SYS_HAS_NONCACHED_MEMORY=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-acer_predator-w6x"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_TARGET_MT7986=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_FIT=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-acer_predator-w6x.dtb"
++CONFIG_LOGLEVEL=7
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_LOG=y
++# CONFIG_BOARD_INIT is not set
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_PROMPT="MT7986> "
++CONFIG_CMD_CPU=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_LINK_LOCAL=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_UUID=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_UBI=y
++CONFIG_ENV_REDUNDANT=y
++CONFIG_ENV_UBI_PART="ubi"
++CONFIG_ENV_UBI_VOLUME="ubootenv"
++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
++CONFIG_ENV_RELOC_GD_ENV_ADDR=y
++CONFIG_ENV_USE_DEFAULT_ENV_TEXT_FILE=y
++CONFIG_ENV_DEFAULT_ENV_TEXT_FILE="defenvs/acer_predator-w6x_env"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_NETCONSOLE=y
++CONFIG_USE_IPADDR=y
++CONFIG_IPADDR="192.168.1.1"
++CONFIG_USE_SERVERIP=y
++CONFIG_SERVERIP="192.168.1.254"
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_CLK=y
++CONFIG_GPIO_HOG=y
++# CONFIG_I2C is not set
++# CONFIG_MMC is not set
++CONFIG_MTD=y
++CONFIG_DM_MTD=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_PHY_FIXED=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PHY=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7986=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_SERIAL_RX_BUFFER=y
++CONFIG_MTK_SERIAL=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPIM=y
++CONFIG_RANDOM_UUID=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
+--- /dev/null
++++ b/defenvs/acer_predator-w6x_env
+@@ -0,0 +1,54 @@
++ethaddr_factory=mtd read u-boot-env 0x40080000 0x0 0x18000 && env import -t 0x40080004 0x18000 ethaddr ; setenv ethaddr_factory
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++bootargs=console=ttyS0,115200n8 console_msg_format=syslog
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
++bootconf=config-1
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-acer_predator-w6x-ubootmod-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-acer_predator-w6x-ubootmod-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-acer_predator-w6x-ubootmod-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-acer_predator-w6x-ubootmod-squashfs-sysupgrade.itb
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= \e[0;34m( ( ( \e[1;39mOpenWrt\e[0;34m ) ) )\e[0m
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=\e[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.\e[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=\e[31mLoad BL2 preloader via TFTP then write to NAND.\e[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=run ubi_read_production && bootm $loadaddr#$bootconf
++boot_recovery=run ubi_read_recovery && bootm $loadaddr#$bootconf
++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
++boot_tftp_forever=while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
++part_fit=fit
++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_read_production=ubi read $loadaddr $part_fit && iminfo $loadaddr && run ubi_prepare_rootfs
++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run ethaddr_factory ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title \e[33m$ver\e[0m"
case "$board" in
abt,asr3000|\
+acer,predator-w6x-ubootmod|\
asus,zenwifi-bt8-ubootmod|\
cmcc,a10-ubootmod|\
cudy,tr3000-v1-ubootmod|\
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7986a-acer-predator-w6x.dtsi"
+
+/ {
+ model = "Acer Predator Connect W6x (Stock Layout)";
+ compatible = "acer,predator-w6x-stock", "mediatek,mt7986a";
+};
+
+&partitions {
+ partition@600000 {
+ label = "dual";
+ reg = <0x600000 0x100000>;
+ read-only;
+ };
+
+ partition@700000 {
+ label = "pot";
+ reg = <0x700000 0x100000>;
+ read-only;
+ };
+
+ partition@800000 {
+ label = "ubi";
+ reg = <0x800000 0x6400000>;
+ };
+
+ partition@6C00000 {
+ label = "ubi1";
+ reg = <0x6C00000 0x6400000>;
+ };
+
+ partition@D000000 {
+ label = "storage";
+ reg = <0xD000000 0x800000>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7986a-acer-predator-w6x.dtsi"
+
+/ {
+ model = "Acer Predator Connect W6x (OpenWrt U-Boot Layout)";
+ compatible = "acer,predator-w6x-ubootmod", "mediatek,mt7986a";
+};
+
+&chosen {
+ rootdisk = <&ubi_rootdisk>;
+ bootargs-append = " root=/dev/fit0 rootwait";
+};
+
+&partitions {
+ partition@600000 {
+ label = "ubi";
+ reg = <0x600000 0xD200000>;
+ compatible = "linux,ubi";
+
+ volumes {
+ ubi_rootdisk: ubi-volume-fit {
+ volname = "fit";
+ };
+ };
+ };
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-/dts-v1/;
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/pinctrl/mt65xx.h>
-
-#include "mt7986a.dtsi"
-
-/ {
- model = "Acer Predator Connect W6x";
- compatible = "acer,predator-w6x", "mediatek,mt7986a";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@40000000 {
- reg = <0 0x40000000 0 0x20000000>;
- device_type = "memory";
- };
-
- reg_1p8v: regulator-1p8v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_5v: regulator-5v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-5V";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- factory {
- label = "factory";
- linux,code = <KEY_RESTART>;
- gpios = <&pio 9 GPIO_ACTIVE_LOW>;
- };
-
- wps {
- label = "wps";
- linux,code = <KEY_WPS_BUTTON>;
- gpios = <&pio 10 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&crypto {
- status = "okay";
-};
-
-ð {
- status = "okay";
-
- gmac0: mac@0 {
- compatible = "mediatek,eth-mac";
- reg = <0>;
- phy-mode = "2500base-x";
-
- fixed-link {
- speed = <2500>;
- full-duplex;
- pause;
- };
- };
- gmac1: mac@1 {
- compatible = "mediatek,eth-mac";
- reg = <1>;
- phy-mode = "2500base-x";
- phy-handle = <&phy6>;
- };
-
- mdio-bus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch@1f {
- compatible = "mediatek,mt7531";
- reg = <31>;
- reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@1 {
- reg = <1>;
- label = "lan1";
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "2500base-x";
-
- fixed-link {
- speed = <2500>;
- full-duplex;
- pause;
- };
- };
- };
- };
-
- phy6: phy@6 {
- compatible = "ethernet-phy-ieee802.3-c45";
- reg = <6>;
-
- };
- };
-};
-
-&pio {
- spi_flash_pins: spi-flash-pins-33-to-38 {
- mux {
- function = "spi";
- groups = "spi0", "spi0_wp_hold";
- };
- conf-pu {
- pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
- drive-strength = <MTK_DRIVE_8mA>;
- bias-disable; /* bias-disable */
- };
- conf-pd {
- pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
- drive-strength = <MTK_DRIVE_8mA>;
- bias-disable; /* bias-disable */
- };
- };
-
- spi_led_pins: spic-pins-29-to-32 {
- mux {
- function = "spi";
- groups = "spi1_2";
- };
- };
-
- wf_2g_5g_pins: wf_2g_5g-pins {
- mux {
- function = "wifi";
- groups = "wf_2g", "wf_5g";
- };
- conf {
- pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
- "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
- "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
- "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
- "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
- "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
- "WF1_TOP_CLK", "WF1_TOP_DATA";
- drive-strength = <MTK_DRIVE_4mA>;
- };
- };
-
- wf_dbdc_pins: wf-dbdc-pins {
- mux {
- function = "wifi";
- groups = "wf_dbdc";
- };
- conf {
- pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
- "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
- "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
- "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
- "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
- "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
- "WF1_TOP_CLK", "WF1_TOP_DATA";
- drive-strength = <MTK_DRIVE_4mA>;
- };
- };
-};
-
-&spi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi_flash_pins>;
- status = "okay";
-
- spi_nand@0 {
- compatible = "spi-nand";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0>;
-
- spi-max-frequency = <52000000>;
- spi-tx-bus-width = <4>;
- spi-rx-bus-width = <4>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "bl2";
- reg = <0x0 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "u-boot-env";
- reg = <0x100000 0x80000>;
- };
-
- partition@180000 {
- label = "factory";
- reg = <0x180000 0x200000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- eeprom_factory_0: eeprom@0 {
- reg = <0x0 0x1000>;
- };
- };
- };
-
- partition@380000 {
- label = "fip";
- reg = <0x380000 0x200000>;
- read-only;
- };
-
- partition@580000 {
- label = "prod";
- reg = <0x580000 0x20000>;
- read-only;
- };
-
- partition@600000 {
- label = "dual";
- reg = <0x600000 0x100000>;
- read-only;
- };
-
- partition@700000 {
- label = "pot";
- reg = <0x700000 0x100000>;
- read-only;
- };
-
- partition@800000 {
- label = "ubi";
- reg = <0x800000 0x6400000>;
- };
-
- partition@6C00000 {
- label = "ubi1";
- reg = <0x6C00000 0x6400000>;
- };
-
- partition@D000000 {
- label = "storage";
- reg = <0xD000000 0x800000>;
- };
- };
- };
-};
-
-&spi1 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi_led_pins>;
- status = "okay";
-
- ws2812b@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "worldsemi,ws2812b";
- reg = <0>;
- spi-max-frequency = <3000000>;
-
- led_status_rgb: led@0 {
- reg = <0>;
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_RGB>;
- color-index = <LED_COLOR_ID_RED LED_COLOR_ID_GREEN LED_COLOR_ID_BLUE>;
- };
- };
-};
-
-&ssusb {
- vusb33-supply = <®_3p3v>;
- vbus-supply = <®_5v>;
- status = "okay";
-};
-
-&trng {
- status = "okay";
-};
-
-&uart0 {
- status = "okay";
-};
-
-&usb_phy {
- status = "okay";
-};
-
-&watchdog {
- status = "okay";
-};
-
-&wifi {
- nvmem-cells = <&eeprom_factory_0>;
- nvmem-cell-names = "eeprom";
- pinctrl-names = "default", "dbdc";
- pinctrl-0 = <&wf_2g_5g_pins>;
- pinctrl-1 = <&wf_dbdc_pins>;
- status = "okay";
-};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ reg = <0 0x40000000 0 0x20000000>;
+ device_type = "memory";
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ factory {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "2500base-x";
+ phy-handle = <&phy6>;
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+
+ phy6: phy@6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <6>;
+
+ };
+ };
+};
+
+&pio {
+ spi_flash_pins: spi-flash-pins-33-to-38 {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+
+ spi_led_pins: spic-pins-29-to-32 {
+ mux {
+ function = "spi";
+ groups = "spi1_2";
+ };
+ };
+
+ wf_2g_5g_pins: wf_2g_5g-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_2g", "wf_5g";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <MTK_DRIVE_4mA>;
+ };
+ };
+
+ wf_dbdc_pins: wf-dbdc-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_dbdc";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <MTK_DRIVE_4mA>;
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+
+ spi_nand@0 {
+ compatible = "spi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bl2";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "u-boot-env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition@180000 {
+ label = "factory";
+ reg = <0x180000 0x200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom@0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ partition@380000 {
+ label = "fip";
+ reg = <0x380000 0x200000>;
+ read-only;
+ };
+
+ partition@580000 {
+ label = "prod";
+ reg = <0x580000 0x20000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_led_pins>;
+ status = "okay";
+
+ ws2812b@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "worldsemi,ws2812b";
+ reg = <0>;
+ spi-max-frequency = <3000000>;
+
+ led_status_rgb: led@0 {
+ reg = <0>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RGB>;
+ color-index = <LED_COLOR_ID_RED LED_COLOR_ID_GREEN LED_COLOR_ID_BLUE>;
+ };
+ };
+};
+
+&ssusb {
+ vusb33-supply = <®_3p3v>;
+ vbus-supply = <®_5v>;
+ status = "okay";
+};
+
+&trng {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+ pinctrl-names = "default", "dbdc";
+ pinctrl-0 = <&wf_2g_5g_pins>;
+ pinctrl-1 = <&wf_dbdc_pins>;
+ status = "okay";
+};
ucidef_set_led_netdev "internet" "INTERNET" "mdio-bus:06:amber:wan" "eth1" "link_10 link_100 link_1000 tx rx"
ucidef_set_led_netdev "internet" "INTERNET" "mdio-bus:06:green:wan" "eth1" "link_2500 tx rx"
;;
-acer,predator-w6x)
+acer,predator-w6x-stock|\
+acer,predator-w6x-ubootmod)
ucidef_set_led_netdev "wan" "wan" "rgb:status" "eth1"
;;
asus,rt-ax52|\
acer,predator-w6d)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 game" eth1
;;
- acer,predator-w6x)
+ acer,predator-w6x-stock|\
+ acer,predator-w6x-ubootmod)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
;;
acer,vero-w6m)
wan_mac=$(mmc_get_mac_ascii u-boot-env WANMAC)
lan_mac=$(mmc_get_mac_ascii u-boot-env LANMAC)
;;
- acer,predator-w6x)
+ acer,predator-w6x-stock|\
+ acer,predator-w6x-ubootmod)
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)
label_mac=$wan_mac
[ "$PHYNBR" = "0" ] && mmc_get_mac_ascii u-boot-env 2gMAC > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && mmc_get_mac_ascii u-boot-env 5gMAC > /sys${DEVPATH}/macaddress
;;
- acer,predator-w6x)
+ acer,predator-w6x-stock|\
+ acer,predator-w6x-ubootmod)
hw_mac_addr="$(mtd_get_mac_ascii u-boot-env ethaddr)"
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 3 > /sys${DEVPATH}/macaddress
ip link set dev game address "$lan_mac"
ip link set dev eth1 address "$wan_mac"
;;
- acer,predator-w6x)
+ acer,predator-w6x-stock|\
+ acer,predator-w6x-ubootmod)
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)
ip link set dev lan1 address "$lan_mac"
case "$board" in
abt,asr3000|\
+ acer,predator-w6x-ubootmod|\
asus,zenwifi-bt8-ubootmod|\
bananapi,bpi-r3|\
bananapi,bpi-r3-mini|\
case "$board" in
abt,asr3000|\
+ acer,predator-w6x-ubootmod|\
asus,zenwifi-bt8-ubootmod|\
bananapi,bpi-r3|\
bananapi,bpi-r3-mini|\
endef
TARGET_DEVICES += acer_predator-w6d
-define Device/acer_predator-w6x
+define Device/acer_predator-w6x-stock
DEVICE_VENDOR := Acer
- DEVICE_MODEL := Predator Connect W6x
- DEVICE_DTS := mt7986a-acer-predator-w6x
+ DEVICE_MODEL := Predator Connect W6x (Stock Layout)
+ DEVICE_DTS := mt7986a-acer-predator-w6x-stock
+ SUPPORTED_DEVICES += acer,predator-w6x
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
KERNEL_IN_UBI := 1
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
-TARGET_DEVICES += acer_predator-w6x
+TARGET_DEVICES += acer_predator-w6x-stock
+
+define Device/acer_predator-w6x-ubootmod
+ DEVICE_VENDOR := Acer
+ DEVICE_MODEL := Predator Connect W6x (OpenWrt U-Boot Layout)
+ DEVICE_DTS := mt7986a-acer-predator-w6x-ubootmod
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-usb3 kmod-leds-ws2812b kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware
+ KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+ IMAGES := sysupgrade.itb
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_IN_UBI := 1
+ UBOOTENV_IN_UBI := 1
+ KERNEL := kernel-bin | gzip
+ KERNEL_INITRAMFS := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+ IMAGE/sysupgrade.itb := append-kernel | \
+ fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
+ ARTIFACTS := preloader.bin bl31-uboot.fip
+ ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr4
+ ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot acer_predator-w6x
+endef
+TARGET_DEVICES += acer_predator-w6x-ubootmod
define Device/acer_vero-w6m
DEVICE_VENDOR := Acer
projects / openwrt / staging / blocktrron.git / commitdiff