--- /dev/null
+--- a/cmd/bootm.c
++++ b/cmd/bootm.c
+@@ -260,6 +260,76 @@ U_BOOT_CMD(
+ /* iminfo - print header info for a requested image */
+ /*******************************************************************/
+ #if defined(CONFIG_CMD_IMI)
++#define SECTOR_SHIFT 9
++static int image_totalsize(struct cmd_tbl *cmdtp, int flag, int argc,
++ char *const argv[], short int in_blocks)
++{
++ ulong addr;
++ void *hdr;
++ uint32_t bsize, tsize = 0;
++ char buf[16];
++
++ if (argc >= 2)
++ addr = simple_strtoul(argv[1], NULL, 16);
++ else
++ addr = image_load_addr;
++
++ hdr = (void *)map_sysmem(addr, 0);
++
++ switch (genimg_get_format(hdr)) {
++ case IMAGE_FORMAT_LEGACY:
++ if(CONFIG_IS_ENABLED(LEGACY_IMAGE_FORMAT))
++ tsize = image_get_image_size(hdr);
++ break;
++ case IMAGE_FORMAT_FIT:
++ if(CONFIG_IS_ENABLED(FIT))
++ tsize = fit_get_totalsize(hdr);
++ break;
++ }
++
++ unmap_sysmem(hdr);
++ if (tsize == 0)
++ return 1;
++
++ bsize = (tsize >> SECTOR_SHIFT) + ((tsize & ((1 << SECTOR_SHIFT) - 1))?1:0);
++
++ if (!in_blocks)
++ snprintf(buf, sizeof(buf), "%x", tsize);
++ else
++ snprintf(buf, sizeof(buf), "%x", bsize);
++
++ if (argc >= 3)
++ return env_set(argv[2], buf);
++ else
++ printf("%s\n", buf);
++
++ return 0;
++}
++
++static int do_imsz(struct cmd_tbl *cmdtp, int flag, int argc,
++ char *const argv[])
++{
++ return image_totalsize(cmdtp, flag, argc, argv, 0);
++}
++
++static int do_imszb(struct cmd_tbl *cmdtp, int flag, int argc,
++ char *const argv[])
++{
++ return image_totalsize(cmdtp, flag, argc, argv, 1);
++}
++
++U_BOOT_CMD(
++ imsz, CONFIG_SYS_MAXARGS, 1, do_imsz,
++ "get image total size (in bytes)",
++ "addr [maxhdrlen] [varname]\n"
++);
++
++U_BOOT_CMD(
++ imszb, CONFIG_SYS_MAXARGS, 1, do_imszb,
++ "get image total size (in blocks)",
++ "addr [maxhdrlen] [varname]\n"
++);
++
+ static int do_iminfo(struct cmd_tbl *cmdtp, int flag, int argc,
+ char *const argv[])
+ {
+--- a/boot/image-fit.c
++++ b/boot/image-fit.c
+@@ -2054,6 +2054,47 @@ static const char *fit_get_image_type_pr
+ return "unknown";
+ }
+
++size_t fit_get_totalsize(const void *fit)
++{
++ int ret, ndepth, noffset, images_noffset;
++ size_t data_size, hdrsize, img_total, max_size = 0;
++ const void *data;
++
++ ret = fdt_check_header(fit);
++ if (ret) {
++ debug("Wrong FIT format: not a flattened device tree (err=%d)\n",
++ ret);
++ return 0;
++ }
++
++ hdrsize = fdt_totalsize(fit);
++
++ /* take care of simple FIT with internal images */
++ max_size = hdrsize;
++
++ images_noffset = fdt_path_offset(fit, FIT_IMAGES_PATH);
++ if (images_noffset < 0)
++ goto out;
++
++ for (ndepth = 0,
++ noffset = fdt_next_node(fit, images_noffset, &ndepth);
++ (noffset >= 0) && (ndepth > 0);
++ noffset = fdt_next_node(fit, noffset, &ndepth)) {
++ if (ndepth == 1) {
++ ret = fit_image_get_data(fit, noffset, &data, &data_size);
++ if (ret)
++ goto out;
++
++ img_total = data_size + (data - fit);
++
++ max_size = (max_size > img_total) ? max_size : img_total;
++ }
++ }
++
++out:
++ return max_size;
++}
++
+ int fit_image_load(struct bootm_headers *images, ulong addr,
+ const char **fit_unamep, const char **fit_uname_configp,
+ int arch, int ph_type, int bootstage_id,
+--- a/include/image.h
++++ b/include/image.h
+@@ -1113,6 +1113,7 @@ int fit_parse_subimage(const char *spec,
+ ulong *addr, const char **image_name);
+
+ int fit_get_subimage_count(const void *fit, int images_noffset);
++size_t fit_get_totalsize(const void *fit);
+ void fit_print_contents(const void *fit);
+ void fit_image_print(const void *fit, int noffset, const char *p);
+
--- /dev/null
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "lan969x.dtsi"
+
+/ {
+ model = "Microchip EV23X71A";
+ compatible = "microchip,ev23x71a", "microchip,lan969x";
+
+ aliases {
+ serial0 = &usart0;
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio 60 GPIO_ACTIVE_LOW>;
+ open-source;
+ priority = <200>;
+ };
+
+ i2c-mux {
+ compatible = "i2c-mux-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-parent = <&i2c3>;
+
+ mux-gpios = <&sgpio_out 0 1 GPIO_ACTIVE_HIGH
+ &sgpio_out 0 2 GPIO_ACTIVE_HIGH
+ &sgpio_out 0 3 GPIO_ACTIVE_HIGH>;
+ idle-state = <0x8>;
+
+ i2c_sfp0: i2c@0 {
+ reg = <0x0>;
+ };
+
+ i2c_sfp1: i2c@1 {
+ reg = <0x1>;
+ };
+
+ i2c_sfp2: i2c@2 {
+ reg = <0x2>;
+ };
+
+ i2c_sfp3: i2c@3 {
+ reg = <0x3>;
+ };
+
+ i2c_poe: i2c@7 {
+ reg = <0x7>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: led-status {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio 61 GPIO_ACTIVE_LOW>;
+ };
+
+ led-sfp1-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <0>;
+ gpios = <&sgpio_out 6 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp1-yellow {
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <0>;
+ gpios = <&sgpio_out 6 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp2-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ gpios = <&sgpio_out 7 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp2-yellow {
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ gpios = <&sgpio_out 7 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp3-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ gpios = <&sgpio_out 8 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp3-yellow {
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ gpios = <&sgpio_out 8 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp4-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ gpios = <&sgpio_out 9 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sfp4-yellow {
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ gpios = <&sgpio_out 9 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ mux-controller {
+ compatible = "gpio-mux";
+ #mux-control-cells = <0>;
+
+ mux-gpios = <&sgpio_out 1 2 GPIO_ACTIVE_LOW>,
+ <&sgpio_out 1 3 GPIO_ACTIVE_LOW>;
+ };
+
+ sfp0: sfp0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp0>;
+ tx-disable-gpios = <&sgpio_out 6 2 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in 6 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in 6 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in 6 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ sfp1: sfp1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out 7 2 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in 7 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in 7 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in 7 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ sfp2: sfp2 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out 8 2 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in 8 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in 8 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in 8 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ sfp3: sfp3 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out 9 2 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in 9 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in 9 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in 9 2 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&flx0 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "okay";
+};
+
+&usart0 {
+ pinctrl-0 = <&fc0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&flx2 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-0 = <&fc2_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&gpio 63 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&flx3 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-0 = <&fc3_pins>;
+ pinctrl-names = "default";
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
+ i2c-sda-hold-time-ns = <1500>;
+ status = "okay";
+};
+
+&gpio {
+ emmc_sd_pins: emmc-sd-pins {
+ /* eMMC_SD - CMD, CLK, D0, D1, D2, D3, D4, D5, D6, D7, RSTN */
+ pins = "GPIO_14", "GPIO_15", "GPIO_16", "GPIO_17",
+ "GPIO_18", "GPIO_19", "GPIO_20", "GPIO_21",
+ "GPIO_22", "GPIO_23", "GPIO_24";
+ function = "emmc_sd";
+ };
+
+ fan_pins: fan-pins {
+ pins = "GPIO_25", "GPIO_26";
+ function = "fan";
+ };
+
+ fc0_pins: fc0-pins {
+ pins = "GPIO_3", "GPIO_4";
+ function = "fc";
+ };
+
+ fc2_pins: fc2-pins {
+ pins = "GPIO_64", "GPIO_65", "GPIO_66";
+ function = "fc";
+ };
+
+ fc3_pins: fc3-pins {
+ pins = "GPIO_55", "GPIO_56";
+ function = "fc";
+ };
+
+ mdio_pins: mdio-pins {
+ pins = "GPIO_9", "GPIO_10";
+ function = "miim";
+ };
+
+ mdio_irq_pins: mdio-irq-pins {
+ pins = "GPIO_11";
+ function = "miim_irq";
+ };
+
+ sgpio_pins: sgpio-pins {
+ /* SCK, D0, D1, LD */
+ pins = "GPIO_5", "GPIO_6", "GPIO_7", "GPIO_8";
+ function = "sgpio_a";
+ };
+
+ usb_ulpi_pins: usb-ulpi-pins {
+ pins = "GPIO_30", "GPIO_31", "GPIO_32", "GPIO_33",
+ "GPIO_34", "GPIO_35", "GPIO_36", "GPIO_37",
+ "GPIO_38", "GPIO_39", "GPIO_40", "GPIO_41";
+ function = "usb_ulpi";
+ };
+
+ usb_rst_pins: usb-rst-pins {
+ pins = "GPIO_12";
+ function = "usb2phy_rst";
+ };
+
+ usb_over_pins: usb-over-pins {
+ pins = "GPIO_13";
+ function = "usb_over_detect";
+ };
+
+ usb_power_pins: usb-power-pins {
+ pins = "GPIO_1";
+ function = "usb_power";
+ };
+
+ ptp_out_pins: ptp-out-pins {
+ pins = "GPIO_58";
+ function = "ptpsync_4";
+ };
+
+ ptp_ext_pins: ptp-ext-pins {
+ pins = "GPIO_59";
+ function = "ptpsync_5";
+ };
+};
+
+&qspi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <100000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ m25p,fast-read;
+ };
+};
+
+&sdmmc0 {
+ pinctrl-0 = <&emmc_sd_pins>;
+ pinctrl-names = "default";
+ max-frequency = <100000000>;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ non-removable;
+ disable-wp;
+ status = "okay";
+};
+
+&tmon {
+ pinctrl-0 = <&fan_pins>;
+ pinctrl-names = "default";
+};
+
+&mdio0 {
+ pinctrl-0 = <&mdio_pins>, <&mdio_irq_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio 62 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ phy3: phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy4: phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy5: phy@5 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <5>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy6: phy@6 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <6>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy7: phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy8: phy@8 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <8>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy9: phy@9 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <9>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy10: phy@10 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <10>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy11: phy@11 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <11>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy12: phy@12 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <12>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy13: phy@13 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <13>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy14: phy@14 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <14>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy15: phy@15 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <15>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy16: phy@16 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <16>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy17: phy@17 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <17>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy18: phy@18 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <18>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy19: phy@19 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <19>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy20: phy@20 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <20>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy21: phy@21 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <21>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy22: phy@22 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <22>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy23: phy@23 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <23>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy24: phy@24 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <24>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy25: phy@25 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <25>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy26: phy@26 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <26>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+
+ phy27: phy@27 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <27>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio>;
+ };
+};
+
+&serdes {
+ status = "okay";
+};
+
+&sgpio {
+ pinctrl-0 = <&sgpio_pins>;
+ pinctrl-names = "default";
+
+ microchip,sgpio-port-ranges = <0 1>, <6 9>;
+ status = "okay";
+
+ gpio@0 {
+ ngpios = <128>;
+ };
+ gpio@1 {
+ ngpios = <128>;
+ };
+};
+
+&switch {
+ pinctrl-0 = <&ptp_out_pins>, <&ptp_ext_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port@0 {
+ reg = <0>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy4>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 0>;
+ };
+
+ port1: port@1 {
+ reg = <1>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy5>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 0>;
+ };
+
+ port2: port@2 {
+ reg = <2>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy6>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 0>;
+ };
+
+ port3: port@3 {
+ reg = <3>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy7>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 0>;
+ };
+
+ port4: port@4 {
+ reg = <4>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy8>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 1>;
+ };
+
+ port5: port@5 {
+ reg = <5>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy9>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 1>;
+ };
+
+ port6: port@6 {
+ reg = <6>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy10>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 1>;
+ };
+
+ port7: port@7 {
+ reg = <7>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy11>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 1>;
+ };
+
+ port8: port@8 {
+ reg = <8>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy12>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 2>;
+ };
+
+ port9: port@9 {
+ reg = <9>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy13>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 2>;
+ };
+
+ port10: port@10 {
+ reg = <10>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy14>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 2>;
+ };
+
+ port11: port@11 {
+ reg = <11>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy15>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 2>;
+ };
+
+ port12: port@12 {
+ reg = <12>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy16>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 3>;
+ };
+
+ port13: port@13 {
+ reg = <13>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy17>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 3>;
+ };
+
+ port14: port@14 {
+ reg = <14>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy18>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 3>;
+ };
+
+ port15: port@15 {
+ reg = <15>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy19>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 3>;
+ };
+
+ port16: port@16 {
+ reg = <16>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy20>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 4>;
+ };
+
+ port17: port@17 {
+ reg = <17>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy21>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 4>;
+ };
+
+ port18: port@18 {
+ reg = <18>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy22>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 4>;
+ };
+
+ port19: port@19 {
+ reg = <19>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy23>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 4>;
+ };
+
+ port20: port@20 {
+ reg = <20>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy24>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 5>;
+ };
+
+ port21: port@21 {
+ reg = <21>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy25>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 5>;
+ };
+
+ port22: port@22 {
+ reg = <22>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy26>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 5>;
+ };
+
+ port23: port@23 {
+ reg = <23>;
+ microchip,bandwidth = <1000>;
+ phy-handle = <&phy27>;
+ phy-mode = "qsgmii";
+ phys = <&serdes 5>;
+ };
+
+ port24: port@24 {
+ reg = <24>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 6>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp0>;
+ microchip,sd-sgpio = <24>;
+ managed = "in-band-status";
+ };
+
+ port25: port@25 {
+ reg = <25>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 7>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp1>;
+ microchip,sd-sgpio = <28>;
+ managed = "in-band-status";
+ };
+
+ port26: port@26 {
+ reg = <26>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 8>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp2>;
+ microchip,sd-sgpio = <32>;
+ managed = "in-band-status";
+ };
+
+ port27: port@27 {
+ reg = <27>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 9>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp3>;
+ microchip,sd-sgpio = <36>;
+ managed = "in-band-status";
+ };
+
+ port29: port@29 {
+ reg = <29>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 11>;
+ phy-handle = <&phy3>;
+ phy-mode = "rgmii";
+ rx-internal-delay-ps = <1000>;
+ tx-internal-delay-ps = <1000>;
+ };
+ };
+};
+
+&usb {
+ status = "okay";
+ pinctrl-0 = <&usb_ulpi_pins>, <&usb_rst_pins>, <&usb_over_pins>, <&usb_power_pins>;
+ pinctrl-names = "default";
+};
projects / openwrt / staging / ldir.git / commitdiff