NEC Aterm WF1200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router with FE
ports, based on AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A-2.5BG2A)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EM2I-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 4x 10/100 Mbps
- switch : Atheros AR9344 (SoC)
- LEDs/Keys (GPIO) : 12x/4x
- note : all LEDs are controlled by ath10k chip (QCA9882)
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8 (U-Boot: 115200n8)
- Power : 12 VDC, 0.7 A (Max. 8 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WF1200HP with router mode
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.10.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with sysupgrade.bin image
sysupgrade <sysuppgrade image>
8. Wait ~120 seconds to complete flashing and rebooting
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WF1200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with the password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, backup the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the
device
9. Replace the bootloader with uboot.bin image (see above)
10. Perform sysupgrade with sysupgrade.bin image (see above)
11. Wait ~120 seconds to complete flashing and rebooting
Notes:
- The stock bootloader requires the unknown filesystem on firmware area
in the flash chip. Booting OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
Known issues:
- All LEDs on the front side are connected to the GPIO controller on the
ath10k chip (QCA9882) and controlled by it. The current ath10k driver
supports only one LED as "ath10k-phyN", but using as a GPIO controller
is not supported yet. As a result, all 12x LEDs on the front side
cannot be controlled by users.
MAC Addresses:
LAN : C0:25:A2:xx:xx:44 (config, 0x6 (hex))
WAN : C0:25:A2:xx:xx:45 (config, 0xc (hex))
2.4 GHz: C0:25:A2:xx:xx:46 (config, 0x0 (hex))
5 GHz : C0:25:A2:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20611
Signed-off-by: Hauke Mehrtens <[email protected]>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ aliases {
+ label-mac-device = ð0;
+ };
+
+ chosen {
+ /*
+ * don't specify bootargs property in DeviceTree to
+ * enable a console with a default baudrate (9600)
+ * or passed console= parameter from the bootloader
+ */
+ /delete-property/ bootargs;
+ stdout-path = &uart;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ button-wps {
+ label = "wps";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+
+ switch-bridge {
+ label = "br";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ debounce-interval = <60>;
+ };
+
+ switch-coverter {
+ label = "cnv";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ debounce-interval = <60>;
+ };
+
+ button-reset {
+ label = "reset";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+ };
+
+ /* all LEDs are connected to ath10k chip (QCA9882) */
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * since the OEM bootloader requires unknown
+ * filesystem on firmware area, needs to be
+ * replaced to u-boot before OpenWrt installation
+ */
+ partition@0 {
+ label = "bootloader";
+ reg = <0x000000 0x020000>;
+ };
+
+ /* not compatible with u-boot */
+ partition@20000 {
+ label = "config";
+ reg = <0x020000 0x010000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_config_0: mac-address@0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_config_6: mac-address@6 {
+ reg = <0x6 0x6>;
+ };
+
+ macaddr_config_c: mac-address@c {
+ reg = <0xc 0x6>;
+ };
+
+ macaddr_config_12: mac-address@12 {
+ reg = <0x12 0x6>;
+ };
+ };
+ };
+
+ partition@30000 {
+ label = "art";
+ reg = <0x030000 0x010000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cal_art_1000: calibration@1000 {
+ reg = <0x1000 0x440>;
+ };
+
+ cal_art_5000: calibration@5000 {
+ reg = <0x5000 0x844>;
+ };
+ };
+ };
+
+ partition@40000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x040000 0x7c0000>;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+
+ nvmem-cells = <&macaddr_config_c>;
+ nvmem-cell-names = "mac-address";
+};
+
+ð1 {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_config_6>;
+ nvmem-cell-names = "mac-address";
+};
+
+&pcie {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x0000 0 0 0 0>;
+
+ nvmem-cells = <&cal_art_5000>, <&macaddr_config_12>;
+ nvmem-cell-names = "calibration", "mac-address";
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ nvmem-cells = <&cal_art_1000>, <&macaddr_config_0>;
+ nvmem-cell-names = "calibration", "mac-address";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344_nec_wf1200.dtsi"
+
+/ {
+ compatible = "nec,wf1200hp", "qca,ar9344";
+ model = "NEC Aterm WF1200HP";
+};
static inline void huawei_ap_init(void) {}
#endif
-#if defined(CONFIG_BOARD_NEC_WG1400HP) || \
+#if defined(CONFIG_BOARD_NEC_WF1200HP) || \
+ defined(CONFIG_BOARD_NEC_WG1400HP) || \
defined(CONFIG_BOARD_NEC_WG1800HP) || \
defined(CONFIG_BOARD_NEC_WG1800HP2) || \
defined(CONFIG_BOARD_NEC_WG2200HP) || \
}
#endif
-#if defined(CONFIG_BOARD_NEC_WG600HP) || \
+#if defined(CONFIG_BOARD_NEC_WF1200HP) || \
+ defined(CONFIG_BOARD_NEC_WG600HP) || \
defined(CONFIG_BOARD_NEC_WR8750N) || \
defined(CONFIG_BOARD_NEC_WR9500N)
endef
TARGET_DEVICES += engenius_enh202-v1
+define Device/nec_wf1200hp
+ DEVICE_MODEL := Aterm WF1200HP
+ SOC := ar9344
+ BLOCKSIZE := 4k
+ IMAGE_SIZE := 7936k
+ NEC_FW_TYPE := H047
+ $(Device/nec-netbsd-aterm)
+ DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct \
+ -uboot-envtools
+ UBOOT_PATH := $$(STAGING_DIR_IMAGE)/$$(SOC)_nec_aterm_fe-u-boot.bin
+endef
+TARGET_DEVICES += nec_wf1200hp
+
define Device/nec_wg600hp
DEVICE_MODEL := Aterm WG600HP
SOC := ar9344
ucidef_add_switch "switch0" \
"0@eth1" "4:lan:1"
;;
+ nec,wf1200hp)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
+ ;;
nec,wg600hp|\
nec,wr8750n|\
nec,wr9500n|\
local board=$(board_name)
case "$board" in
+ nec,wf1200hp|\
nec,wg600hp|\
nec,wr8750n|\
nec,wr9500n)
projects / openwrt / openwrt.git / commitdiff